Home › ENGINE › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. DISCONNECT HEATER WATER HOSE ASSEMBLY


A225928
  1. Disconnect the 2 hoses and remove the heater water hose assembly from the No. 1 water outlet pipe and rear water by-pass joint.



2. REMOVE EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)


A225367
  1. Remove the 3 nuts and emission control valve set from the cylinder head cover sub-assembly.



3. REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)


A225368
  1. Remove the 3 nuts and No. 2 emission control valve set from the cylinder head cover sub-assembly LH.



4. REMOVE IGNITION COIL ASSEMBLY


A224724
  1. Remove the 6 bolts and 6 ignition coil assemblies from the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.



5. REMOVE REAR CYLINDER HEAD COVER


    A224695
  1. Remove the 3 bolts and cover.



6. REMOVE FUEL PIPE SUB-ASSEMBLY


A225938
  1. Disconnect the 2 fuel pipes from the fuel delivery pipe sub-assembly (Click here).

  1. Remove the 2 bolts, No. 1 fuel pipe and No. 2 fuel pipe from the cylinder head cover sub-assembly LH.



7. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    A223037
  1. Disconnect the 6 fuel injector connectors.

  1. Remove the 4 bolts and fuel delivery pipe together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the injectors when removing the fuel delivery pipe.



8. REMOVE FUEL INJECTOR ASSEMBLY


    A223038E02
  1. Pull the 6 fuel injectors from the fuel delivery pipe.
    Text in Illustration 
    *1
    Fuel Delivery Pipe
    *2
    Fuel Injector

  1. Remove the O-ring and injector vibration insulator from each fuel injector.



9. REMOVE INTAKE MANIFOLD


    A244715
  1. Remove the bolt and the wire harness clamp bracket from the intake manifold.



    A221466E02
  1. Remove the 4 nuts, 6 bolts and intake manifold from the cylinder head sub-assembly.
    Text in Illustration 
    *1
    Nut

  1. Remove the No. 1 intake manifold to head gasket and No. 2 intake manifold to head gasket from the cylinder head sub-assembly.



10. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


A158544
  1. Remove the bolt and No. 1 idler pulley sub-assembly from the timing chain cover sub-assembly.



11. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


A223006
  1. for Cover Separate Type:
    Remove the 2 bolts, 2 idler pulley cover plates, 2 No. 2 idler pulley sub-assemblies, and 2 No. 2 idler pulley cover plates from the timing chain cover sub-assembly.

  1. for Cover Integrated Type:
    Remove the 2 bolts and 2 No. 2 idler pulley sub-assemblies from the timing chain cover sub-assembly.



12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


A222180
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.



13. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


A222114
  1. Remove the engine oil level dipstick from the engine oil level dipstick guide.

  1. Remove the bolt and engine oil level dipstick guide from the timing chain cover sub-assembly and guide hole.

  1. Remove the O-ring from the engine oil level dipstick guide.



14. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    A221156
  1. Remove the 3 bolts and front No. 1 engine mounting bracket LH from the cylinder block sub-assembly.



15. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A221155
  1. Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.



16. REMOVE FLYWHEEL RING GEAR (for Manual Transmission)

CAUTION:
Wear protective gloves. Hot areas on the flywheel ring gear may injure your hands.

HINT:
If the flywheel ring gear is deformed or the gears are damaged, replace it.



    A177669E01
  1. Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

  1. Temporarily install 6 bolts (8 mm (0.315 in.) x 1.25 pitch) with a length of 70 mm (2.76 in.) or more to the flywheel.

  1. Uniformly tighten the 6 bolts in the order shown in the illustration.

  1. Remove the flywheel ring gear from the flywheel.