Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM

INTUITIVE PARKING ASSIST SYSTEM > Back Sonar Sensor Circuit

for Preparation Click here


DESCRIPTION

This circuit shows the sensor power supply, sensor GND and sensor signal wires between the clearance warning ECU and No. 1 ultrasonic sensors. The No. 1 ultrasonic sensors are digital sensors.

WIRING DIAGRAM


E160767E03


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - NO. 1 ULTRASONIC SENSOR LH)
  1. Disconnect the E80 clearance warning ECU connector.

  1. Disconnect the d2 No. 1 ultrasonic sensor LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E80-24 (BOR) - d2-1 (BI)
    Always
    Below 1 Ω
    E80-6 (SOR) - d2-3 (SI)
    E80-22 (E2) - d2-5 (EI)
    E80-24 (BOR) - Body ground
    Always
    10 kΩ or higher
    E80-6 (SOR) - Body ground
    E80-22 (E2) - Body ground

  1. Reconnect the clearance warning ECU connector.

  1. Reconnect the No. 1 ultrasonic sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE NO. 1 ULTRASONIC SENSOR LH
  1. Replace the No. 1 ultrasonic sensor LH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


3.CHECK INTUITIVE PARKING ASSIST SYSTEM
  1. Check the operation of the Intuitive parking assist system (Click here).
    Result 
    Result
    Proceed to
    Intuitive parking assist system malfunction
    A
    Intuitive parking assist system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR LH MALFUNCTION)
A


4.CHECK HARNESS AND CONNECTOR (ULTRASONIC SENSOR LH - ULTRASONIC SENSOR RH)
  1. Disconnect the d2 No. 1 ultrasonic sensor LH connector.

  1. Disconnect the d1 No. 1 ultrasonic sensor RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    d2-2 (BO) - d1-1 (BI)
    Always
    Below 1 Ω
    d2-4 (SO) - d1-3 (SI)
    d2-6 (EO) - d1-5 (EI)
    d2-2 (BO) - Body ground
    Always
    10 kΩ or higher
    d2-4 (SO) - Body ground
    d2-6 (EO) - Body ground

  1. Reconnect the No. 1 ultrasonic sensor connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE NO. 1 ULTRASONIC SENSOR RH
  1. Replace the No. 1 ultrasonic sensor RH with a normally functioning sensor (Click here).

    HINT:
    All the ultrasonic sensors are the same. Switch the right and left sensors to confirm if the sensors function normally.


NEXT


6.CHECK INTUITIVE PARKING ASSIST SYSTEM
  1. Check the operation of the Intuitive parking assist system (Click here).
    Result 
    Result
    Proceed to
    Intuitive parking assist system malfunction
    A
    Intuitive parking assist system normal operation
    B



B
END (NO. 1 ULTRASONIC SENSOR RH MALFUNCTION)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)