Home › ENGINE › 1GR-FE INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > INSTALLATION

for Preparation Click here



1. INSTALL STUD BOLT
  1. Using "Torx" socket wrench E8, install the 2 stud bolts to the intake manifold.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



2. INSTALL INTAKE MANIFOLD


    A221467E01
  1. Install the new No. 1 intake manifold to head gasket and No. 2 intake manifold to head gasket to the cylinder head sub-assembly.
    Text in Illustration 
    *1
    No. 1 Intake Manifold To Head Gasket
    *2
    No. 2 Intake Manifold To Head Gasket
    *a
    Bank 2 Identification Mark
    V100135
    Front of Vehicle

    NOTICE:
    1. When installing the No. 1 intake manifold to head gasket and No. 2 intake manifold to head gasket, pay attention to the Bank 1 and Bank 2 sides.
    2. Align the port holes of the gasket and cylinder head sub-assembly.

  1. Temporarily install the intake manifold to the cylinder head sub-assembly with the 4 nuts and 6 bolts.



    A221466E03
  1. Install and uniformly tighten the 4 nuts and 6 bolts in several steps in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the wire harness clamp bracket to the intake manifold with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 70 in.*lbf }



3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


    A223047E02
  1. Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.
    Text in Illustration 
    *a
    Turn

  1. Temporarily install the 6 bolts, which are used to hold the fuel delivery pipe, to the intake manifold.

  1. Check that the fuel injectors rotate smoothly.

    HINT:
    If the fuel injectors do not rotate smoothly, replace the O-ring of any injector that does not rotate smoothly.

  1. Position the fuel injector connectors facing outward.

  1. Tighten the 6 bolts, which are used to hold the fuel delivery pipe, to the intake manifold.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 6 fuel injector connectors.



4. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY
  1. Connect the No. 2 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting part.
    2. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
    3. After connecting, check that the pipe and connector are securely connected by pulling on them.



5. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
  1. Connect the No. 1 fuel pipe sub-assembly (Click here).

    NOTICE:
    1. Check that there are no scratches or foreign objects on the connecting part.
    2. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
    3. After connecting, check that the pipe and connector are securely connected by pulling on them.



6. INSTALL REAR CYLINDER HEAD COVER
  1. Temporarily install the cover with the 3 bolts.



    A224695E01
  1. Tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



7. INSTALL INTAKE AIR SURGE TANK


    A244714
  1. Install a new air surge tank to intake manifold gasket to the intake air surge tank.

  1. Using an 8 mm socket hexagon wrench, temporarily install the intake air surge tank to the intake manifold with the 4 bolts and 2 nuts.



    A221465E07
  1. Using an 8 mm socket hexagon wrench, install and uniformly tighten the 4 bolts and 2 nuts in several steps in the sequence shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    A221460E03
  1. Install the throttle body bracket to the intake air surge tank with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A221462E02
  1. Install the No. 1 surge tank stay to the intake air surge tank with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Engage the clamp and connect the wire harness to the No. 1 surge tank stay.



    A244712E01
  1. Install the No. 2 surge tank stay to the intake air surge tank with the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the wire harness clamp bracket to the No. 2 surge tank stay with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A171130E01
  1. Connect the No. 1 ventilation hose to the intake air surge tank with the hose clip.
    Text in Illustration 
    *a
    View A
    *b
    Hose Paint Mark
    *c
    Front of Vehicle

    HINT:
    Make sure the No. 1 ventilation hose and hose clip are facing the directions shown in the illustration.



    A171131E01
  1. Connect the No. 1 fuel vapor feed hose to the vacuum switching valve with the hose clip.
    Text in Illustration 
    *a
    View A
    *b
    Hose Paint Mark
    *c
    Upper of Vehicle

    HINT:
    Make sure the No. 1 fuel vapor feed hose and hose clip are facing the directions shown in the illustration.

  1. Connect the No. 1 vacuum switching valve connector.

  1. Connect the 2 clamps of the heater water hose to the intake air surge tank.



    A244689E01
  1. Connect the No. 4 water by-pass hose and No. 5 water by-pass hose to the water inlet housing with the 2 clips.
    Text in Illustration 
    *a
    View A
    *b
    Hose Paint Mark
    *c
    Front of Vehicle

    HINT:
    Make sure the No. 4 water by-pass hose, the No. 5 water by-pass hose and the 2 hose clips are facing the directions shown in the illustration.

  1. Connect the throttle with motor body assembly connector.



8. INSTALL AIR HOSE ASSEMBLY (w/ Secondary Air Injection System)


    A226132E02
  1. Install the air hose assembly to the No. 2 emission control valve set with the hose clip.
    Text in Illustration 
    *a
    View A
    *b
    Hose Paint Mark
    *c
    Upper of Vehicle
    *d
    Protrusion of No. 2 Emission Control Valve Set

    HINT:
    1. Align the paint mark of the air hose assembly with the protrusion of the No. 2 emission control valve set as shown in the illustration.
    2. Make sure the hose clip is facing in the direction shown in the illustration.

  1. Connect the air hose assembly to the timing chain cover sub-assembly and No. 1 surge tank stay with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A226131E02
  1. Connect the air hose assembly to the No. 1 emission control valve set with the hose clip.
    Text in Illustration 
    *a
    View A
    *b
    Hose Paint Mark
    *c
    Upper of Vehicle
    *d
    Protrusion of No. 1 Emission Control Valve Set

    HINT:
    1. Align the paint mark of the air hose assembly with the protrusion of the No. 1 emission control valve set as shown in the illustration.
    2. Make sure the hose clip is facing in the direction shown in the illustration.

  1. Connect the air hose assembly to the timing chain cover sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. CONNECT NO. 1 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)


    A244711E01
  1. Connect the No. 1 air injection system hose to the air hose assembly with the hose clip.
    Text in Illustration 
    *a
    View A
    *b
    Hose Paint Mark
    *c
    Upper of Vehicle
    *d
    Protrusion of Air Hose Assembly

    HINT:
    1. Align the paint mark of the No. 1 air injection system hose with the protrusion of the air hose assembly as shown in the illustration.
    2. Make sure the hose clip is facing in the direction shown in the illustration.



10. INSTALL AIR CLEANER HOSE ASSEMBLY


    A244693E01
  1. Install the air cleaner hose assembly to the air cleaner cap sub-assembly and intake air surge tank with the 2 hose clamps.
    Text in Illustration 
    *a
    View A
    *b
    View B
    *c
    Hose Paint Mark
    *d
    Upper of Vehicle
    *e
    Protrusion of Air Cleaner Cap Sub-assembly
    *f
    Protrusion of Intake Air Surge Tank
    *g
    Indentation of Air Hose Assembly

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    HINT:
    1. Align the protrusions of the air cleaner cap sub-assembly and the intake air surge tank with the indentation of the air hose assembly.
    2. Make sure the 2 hose clamps are facing in the directions shown in the illustration.

  1. Connect the air cleaner hose assembly to the resonator bracket with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Engage the clamp and connect the wire harness to the air cleaner hose assembly.

  1. Connect the vacuum hose to the air cleaner hose assembly.

  1. Connect the ventilation hose to the air cleaner hose assembly with the hose clip.

    HINT:
    Make sure the ventilation hose and hose clip are facing the directions shown in the illustration.



11. ADD ENGINE COOLANT
  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

  1. Remove the vinyl hose from the radiator drain cock of the radiator assembly.

  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    for Automatic Transmission
    9.8 liters (10.4 US qts, 8.6 Imp. qts)
    for Manual Transmission
    9.4 liters (9.9 US qts, 8.3 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the engine coolant level. If the engine coolant level is low, add engine coolant.



    A220212E03
  1. Slowly pour engine coolant into the radiator reservoir until it reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the radiator reserve tank cap sub-assembly.

  1. Install the radiator cap sub-assembly.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass, and then remove the radiator cap sub-assembly and check the engine coolant level. If the engine coolant level has decreased, add engine coolant.*3

  1. Repeat steps *1, *2 and *3 until the engine coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the No. 1 radiator hose will flow into the radiator assembly if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap sub-assembly.*4

  1. Set the air conditioning as follows.*5
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the engine coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator assembly and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir becomes empty, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the Full line.
    2. Do not start the engine when there is no engine coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough engine coolant, the engine may burn out or overheat.

    HINT:
    1. Press the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature, and then remove the radiator cap sub-assembly and check the engine coolant level.*7

    CAUTION:
    Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the engine coolant level has decreased, add engine coolant and warm up the engine until the thermostat opens.*8



    A220212E03
  1. If the engine coolant level has not decreased, check that the engine coolant level in the radiator reservoir is at the Full line.
    If the engine coolant level is below the Full line, repeat steps *4 through *8.
    If the engine coolant level is above the Full line, drain engine coolant until the engine coolant level reaches the Full line.
    Text in Illustration 
    *a
    Full Line

  1. Install the service hole cover to the engine under cover.



12. INSPECT FOR COOLANT LEAK

CAUTION:
To avoid being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion may cause hot engine coolant and steam to blow out from the radiator.

  1. Fill the radiator with engine coolant, and then attach a radiator cap tester.

  1. Warm up the engine.



    A220211E01
  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
    Text in Illustration 
    *1
    Radiator Cap Tester



13. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

    NOTICE:
    Do not start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Speed / ON.

  1. Check fuel pump operation.

    1. Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.
      If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.



14. INSTALL V-BANK COVER
  1. Engage the 2 hooks and install the V-bank cover to the No. 1 V-bank cover bracket.

  1. Align the 2 V-bank cover grommets with the 2 pins and press down on the V-bank cover to engage the pins.



15. INSPECT INTAKE SYSTEM