DTC P144C Open in Secondary Air Injection System Heater Control Circuit |
DTC P144D Short in Secondary Air Injection System Heater Control Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P144C | Open or short in the air pump heater relay (AIR PMP HTR) circuit for 5 seconds (1 trip detection logic). |
|
| P144D | Open or short in the air pump heater relay (AIR PMP HTR) circuit for 5 seconds (1 trip detection logic). |
|
| Related DTCs | P144C: Air pump heater relay circuit range check (Low voltage) P144D: Air pump heater relay circuit range check (High voltage) |
| Required Sensors/Components (Main) | Air pump heater relay (AIR PMP HTR) |
| Required Sensors/Components (Related) | - |
| Frequency of operation | Continuous |
| Duration | 5 seconds |
| MIL operation | Immediate |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Current command to air pump heater relay (AIR PMP HTR) | ON |
| Last command to air pump heater relay (AIR PMP HTR) | ON |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not stored | None |
| Current command to air pump heater relay (AIR PMP HTR) | OFF |
| Last command to air pump heater relay (AIR PMP HTR) | OFF |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Air pump heater relay (AIR PMP HTR) output terminal voltage level | Low |
| Air pump heater relay (AIR PMP HTR) output terminal voltage level | High |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.INSPECT AIR PUMP HEATER RELAY (AIR PMP HTR) |
![]() |
Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage not applied | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK AIR PUMP HEATER RELAY (AIR PMP HTR) (POWER SOURCE) |
Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.
Turn the ignition switch to ON.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (Air pump heater relay (AIR PMP HTR)) - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | Air Pump Heater Relay (AIR PMP HTR) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY (AIR PMP HTR)) |
Remove the air pump heater relay (AIR PMP HTR) from the engine room relay block.
Disconnect the B49 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (Air pump heater relay (AIR PMP HTR)) - B49-20 (HAI1) | Always | Below 1 Ω |
| 1 (Air pump heater relay (AIR PMP HTR)) or B49-20 (HAI1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||