Home › SUSPENSION & AXLE › AXLE › REAR AXLE SHAFT

REAR AXLE SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL REAR AXLE SHAFT OIL SEAL


    C102278E01
  1. Using SST and a hammer, install a new rear axle shaft oil seal.

    SST
    09554-22010  

  1. Apply MP grease to the oil seal lip.



2. INSTALL BEARING RETAINER O-RING
  1. Apply MP grease to the bearing retainer O-ring.

  1. Install the bearing retainer O-ring to the rear axle shaft housing.



3. INSTALL REAR AXLE SHAFT WITH BACKING PLATE


    C102664J01
  1. Install the rear axle shaft with backing plate to the rear axle shaft housing with the 4 nuts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the rear axle shaft oil seal.
    2. Be careful not to damage the skid control rotor rear.



4. INSTALL REAR SPEED SENSOR (w/ ABS)
  1. Install the new speed sensor O-ring to the rear speed sensor.



    C102662J01
  1. Install the rear speed sensor to the rear axle shaft housing with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Be careful not to damage the rear speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.
    3. Do not twist the speed sensor wire when installing the speed sensor.



5. INSTALL REAR WHEEL BRAKE CYLINDER ASSEMBLY


    C102608
  1. Install the wheel brake cylinder assembly with the 2 bolts.

    Torque:
    9.5 N*m{ 97 kgf*cm , 84 in.*lbf }

  1. Using SST, connect the brake tube.

    SST
    09023-00101  

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }



6. APPLY HIGH TEMPERATURE GREASE


    C102609E01
  1. Apply high temperature grease to the shoe attached surface of the backing plate.



7. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3


    C102159
  1. Install the parking brake cable assembly No.3 to the rear brake backing plate with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



8. INSTALL PARKING BRAKE SHOE STRUT SET


    F042695E01
  1. Apply the high temperature grease to the adjusting bolt.

  1. Install the tension spring to the show strut set.



9. INSTALL REAR BRAKE SHOE


    C102607E01
  1. Using pliers, install the rear brake shoe, shoe strut set, rear cushion lever and shoe lever with a new C-washer.



    C102606
  1. Connect the parking brake cable No.3 to the front brake shoe.



    C102603E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down cup.

    SST
    09718-00010  



10. INSTALL FRONT BRAKE SHOE
  1. Install the return spring to each brake shoe.



    C102604E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down cup.

    SST
    09718-00010  



    C102667
  1. Install the brake shoe lower strut.

    NOTICE:
    Make sure that the shoe lower strut and brake rear cushion lever are securely engaged.



    C102600
  1. Using needle-nose pliers, install the tension spring.



11. CONNECT PARKING BRAKE SHOE STRUT SET


    C102599E01
  1. Using SST, install the upper side tension spring.

    SST
    09703-30011  



12. INSTALL AUTOMATIC ADJUST LEVER


    C102605
  1. Install the automatic adjust lever and tension spring.

    NOTICE:
    Make sure to install the automatic adjust lever between the groove of the shoe strut set and brake shoe.



13. INSPECT REAR DRUM BRAKE


  1. Check the each part is installed properly.


    C102669E01

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and drum.

  1. If they are not installed correctly, reinstall them as shown in the illustration.



14. INSTALL REAR AXLE BRAKE DRUM GASKET
  1. Install the new brake drum gasket to the rear axle shaft.



15. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY


16. ADJUST REAR DRUM BRAKE SHOE CLEARANCE


    C102598E01
  1. Using a screwdriver from a service hole, turn the adjuster to expand the shoes so that the brake shoes touch the brake drum.



    C102597E01
  1. Using another screwdriver, push up the automatic adjust lever and turn the adjuster to contract the shoes so that the brake shoe does not touch the brake drum. Then turn the adjuster another 180 degrees to further contract the shoes.

  1. Install the hole plug.



17. ADD BRAKE FLUID


C106088

Fluid:
SAE J1704 or FMVSS No. 116 DOT3 or equivalent



18. BLEED BRAKE LINE
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times and loosen the bleeder plug with the pedal held down.

  1. At the point where the fluid stops coming out, tighten the bleeder plug and release the brake pedal.

  1. Repeat this procedure until the air in the brake fluid is completely bled out.

  1. Tighten the bleeder plug.

    1. Front bleeder plug:

      Torque:
      10.8 N*m{ 110 kgf*cm , 8 ft.*lbf }

    2. Rear bleeder plug:

      Torque:
      11.0 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



19. INSPECT BRAKE FLUID LEVEL
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1704 or FMVSS No.116 DOT3 or equivalent



20. INSTALL REAR WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }



21. INSPECT PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Pull firmly on the parking brake control handle.

  1. Release the parking brake lock, and return the parking brake control handle to its off position.

  1. Slowly pull the parking brake control handle all the way up, and count the number of clicks.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf)

    HINT:
    1. If the number of clicks falls outside of the specified range, release the parking brake lock and adjust it.
    2. If there are fewer clicks than the specified value, loosen the parking brake wire adjustment nut an the lock nut. With the parking brake cable loosened, adjust the clearance between the brake drum and lining.



22. ADJUST PARKING BRAKE CONTROL HANDLE TRAVEL
  1. Lift the vehicle



    C102142E01
  1. Depress the parking brake handle. Hold the parking brake adjusting nut using a wrench, and loosen the lock nut.

  1. Turn the parking brake adjusting nut until the parking brake handle travel meets the above specification.

    Parking brake control handle travel:
    10 to 16 clicks at 200 N (20 kgf, 44 lbf)

  1. Count the number of clicks after depressing and releasing the parking brake control handle 3 or 4 times.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake control handle, check that the parking brake indicator light comes on.

    Standard:
    Brake warning light always comes on at the first click.

  1. Hold the parking brake adjusting nut using a wrench, and tighten the lock nut.

    Torque:
    14.5 N*m{ 148 kgf*cm , 11 ft.*lbf }

  1. Lower the vehicle.



23. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS)
(Click here)