Home › TRANSMISSION ยท CLUTCH › CLUTCH PEDAL

CLUTCH PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL CLUTCH PEDAL SPRING HOLDER


    C114261E01
  1. Apply MP grease to the inside of a new clutch pedal spring holder.

  1. Install the clutch pedal spring holder.



2. INSTALL CLUTCH PEDAL PAD
  1. Install the clutch pedal pad to the clutch pedal.



3. INSTALL CLUTCH PEDAL NO.1 CUSHION


    C102633
  1. Using needle-nose pliers, install the clutch pedal No.1 cushion to the clutch pedal.



4. INSTALL CLUTCH PEDAL SHAFT COLLAR


    C102648E02
  1. Apply MP grease to the inner, outer and end surfaces of 2 new pedal bushings.

  1. Install the clutch pedal shaft collar and 2 pedal bushings to the clutch pedal.



5. INSTALL CLUTCH PEDAL SUB-ASSEMBLY


    C114260E01
  1. Align the matchmarks on the clutch pedal and clutch pedal support.

  1. Install the clutch pedal to the clutch pedal support with the pedal shaft, washer, and nut.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



6. INSTALL TURNOVER SPRING SEAT COMPRESSION SPRING


    C105011E01
  1. Apply MP grease to the sliding portion of the spring.

  1. Install the turn over spring seat compression spring.



7. INSTALL CLUTCH PEDAL SPRING (2KD-FTV ENGINE TYPE)


    C114269E02
  1. Apply MP grease No.2 to the sliding portion of the spring.



    C104825E01
  1. Install the clutch pedal spring.

    NOTICE:
    Be sure to install the spring with its end facing upward.

  1. Install a new E-ring.



8. INSTALL CLUTCH PEDAL SUPPORT SUB-ASSEMBLY


    C114263E01
  1. Aligning the clip (clutch pedal support side) with the hole of the bracket on the vehicle, install the clutch pedal support.

    NOTICE:
    Make sure that the clip (clutch pedal support side) is securely engaged in the hole of the bracket on the vehicle.



    C114259E01
  1. Install the clutch pedal support with the 2 bolts.

    Torque:
    Bolt A:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Bolt B:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



    C102635E01
  1. Apply MP grease to the sliding portions of the push rod clevis and clutch pedal.

  1. Install the push rod clevis to the cutout of the pedal from the right side of the vehicle and push it downward.

    NOTICE:
    Check that the push rod cannot be turned 30° or more in order to confirm that the clevis is securely engaged in the pedal.



9. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY


    C105013
  1. Install the clutch master cylinder with the 2 nuts.

    Torque:
    14 N*m{ 145 kgf*cm , 10 ft.*lbf }



10. INSPECT AND ADJUST CLUTCH PEDAL HEIGHT
(Click here)


11. INSTALL AIR DUCT NO.1 (for RHD)


12. INSTALL WASHER TANK AND PUMP ASSEMBLY (for LHD)


13. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    B102832E01
  1. Engage the 8 claws and install the instrument panel finish panel lower center.



14. INSTALL SHIFTING HOLE COVER ASSEMBLY


    B102831E01
  1. Manual Transmission:
    Engage the 6 claws and install the shifting hole cover assembly.

  1. Automatic Transmission:
    Engage the 8 claws and install the sifting hole cover assembly.



15. INSTALL SHIFT LEVER KNOB


16. INSTALL PARKING BRAKE HOLE COVER


    B102829E01
  1. Engage the 6 claws and install the parking brake hole cover.



17. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY NO.1


    B102828E01
  1. Engage the 3 claws.

  1. Install the instrument panel No.1 under cover sub-assembly with the 2 clips.



18. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    B102827E01
  1. Engage the 4 clips (B).

  1. Install the instrument panel finish panel lower with the 2 clips (A).



19. CONNECT BATTERY NEGATIVE CABLE


20. PERFORM INITIALIZATION
Some systems need initialization when disconnecting the cable from the negative battery terminal. (Click here)