Home › TRANSMISSION ยท A343E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCONNECT BATTERY NEGATIVE TERMINAL CABLE


2. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY


    C102919
  1. Remove the transmission oil level gage sub assembly from the transmission oil filler tube.



3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.2


4. REMOVE ENGINE UNDER COVER NO.1


5. REMOVE ENGINE SIDE UNDER COVER LH


6. REMOVE ENGINE SIDE UNDER COVER RH


7. DRAIN AUTOMATIC TRANSMISSION FLUID


    C101769E01
  1. Drain the automatic transmission fluid and remove the drain plug and gasket.

  1. Install the drain plug with a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



8. REMOVE PROPELLER SHAFT ASSEMBLY


    C102185E01
  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.



    C102186E01
  1. Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  



9. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. w/ Secondary air infection system:

    1. Disconnect the fuel ratio sensor connector.

    2. Remove the fuel ratio sensor. (Click here)

  1. For unleaded gasoline engine:

    1. Disconnect the oxygen sensor connector.

    2. Remove the oxygen sensor. (Click here)

  1. Remove the 4 bolts, 2 nuts, and 2 compression springs.

  1. Remove the 2 gaskets from the exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front.



10. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


    C102934E01
  1. Remove the 2 bolts transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.



11. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C102933E05
  1. Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever assembly.

  1. Remove the clip and disconnect the transmission control cable assembly from the transmission control cable bracket.



12. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1


    C102931E02
  1. Remove the 2 bolts and transmission control cable bracket to the automatic transmission assembly.



13. REMOVE STARTER ASSEMBLY


    A102709E01
  1. Remove the 2 bolts, then remove the ground cable and bracket.



    A113538E02
  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the 2 bolts and the starter assembly.



14. DISCONNECT OIL COOLER TUBE


  1. Remove the 3 bolts and disconnect the 3 cooler tube clamps.


    C102932



    C102930E01
  1. Using SST disconnect the 2 oil cooler tubes from the automatic transmission assembly.

    SST
    09023-12701  



15. DISCONNECT CONNECTOR


    C101834E03
  1. Remove the heat insulator from the park/neutral position switch assembly with 2 bolts.



    C102929E04
  1. Disconnect the park/neutral position switch connector.



    C101774E02
  1. Disconnect the connector of speed sensor (SP2) connector and transmission wire connector.



    C102928E01
  1. Disconnect the connector of speed sensor (NCO) connectorand temperature sensor.



16. DISCONNECT WIRE HARNESS


    C102927E01
  1. Remove the 3 bolts and disconnect the wire harness from the automatic transmission assembly .



17. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C102926E01
  1. Remove the flywheel housing dust seal from the automatic transmission assembly.



    C102925E01
  1. Remove the torque converter clutch setting bolts with 6 bolts.



18. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


    C102924E01
  1. Support the automatic transmission assembly with a transmission jack.



19. DISCONNECT ENGINE MOUNTING INSULATOR ASSEMBLY REAR


    C101781
  1. Disconnect the engine mounting insulator assembly rear with bolt, nut and 2 washers.



20. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    C103762
  1. Remove the automatic transmission assembly with 8 bolts.



21. REMOVE ENGINE MOUNTING INSULATOR ASSEMBLY REAR


    C102922E01
  1. Remove the 4 bolts and engine mounting insulator assembly rear from the automatic transmission assembly.



22. REMOVE BREATHER PLUG HOSE


    C103234E01
  1. Remove the breather plug hose from the automatic transmission assembly with a bolt.



23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


    C101843E02
  1. Put matchmarks on the transmission case and torque converter assembly.

  1. Remove the torque converter assembly from the automatic transmission assembly.



24. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY


    D029377E02
  1. Inspect the one-way clutch.

    1. Install the SST so that it fits in the notch of the converter hub and the outer race of the one-way clutch.

      SST
      09350-32014   (09351-32010, 09351-32020)

    2. Install the SST (Stopper) from the sleeve of torque converter assembly and engage serration of stater slight washer.

    3. Stand up the torque converter and turn the SST (tool ).

      SST
      09350-32014   (09351-32010, 09351-32020)

      Standard:
      Check if it rotates smoothly when turned clockwise and locks up when turned counter clockwise.



    D025367E01
  1. Determine the condition of the torque converter clutch assembly.

    1. If the inspection result of the torque converter clutch assembly meets the following item, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in the N position.
      The one-way clutch is free or locked in both directions.
      Fine powder exceeding the sample limit is identified in ATF. (See the sample.)

      HINT:
      1. The sample shows the auto fluid of approximately 0.25 liters (0.26 US qts, 0.22 lmp, qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation face up.



    C011090
  1. Clean and check the oil cooler and oil pipe line.

    1. If the torque converter clutch is inspected or exchange the ATF, is exchanged, clean the oil cooler and oil pipe line.

      HINT:
      1. Spray compressed air of 196 kPa (2kgf/cm2, 28 psi) from the inlet hose.
      2. If plenty of fine powders are identified in the ATF, add a new ATF using a bucket pump and clean it again.

    2. If the ATF is cloudy, inspect the oil cooler.