Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > REMOVAL

for Preparation Click here



1. SEPARATE BATTERY NEGATIVE TERMINAL


2. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)


3. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Remove the radiator cap.



  1. Loosen the radiator drain cock plug and a cylinder block drain cock plug. Then drain the coolant.


    A103477E01



4. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
  1. Perform the same procedure as above on the opposite side.



5. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
  1. Perform the same procedure as above on the opposite side.



6. REMOVE FRONT DOOR SCUFF PLATE RH


7. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Roll up the carpet, and remove the engine service hole sub cover assembly.



8. REMOVE FAN AND GENERATOR V BELT


    A102808E03
  1. Remove the drive belt by rotating the tensioner pulley in clockwise direction to loosen its tension with the pulley set bolt of the tensioner.



9. SEPARATE VANE PUMP OIL RESERVOIR ASSEMBLY


    C101999E01
  1. Remove the 2 bolts and vane pump oil reservoir assembly.

    NOTICE:
    Suspend the vane pump oil reservoir assembly with wire to prevent power steering fluid from spilling out.



10. REMOVE TIMING BELT NO.1 COVER
  1. Remove the wire harness clamp.



    A102815
  1. Remove the 6 bolts and timing belt cover No.1.



11. REMOVE INJECTION PIPE
SST
09023-12701  


  1. Remove the injection pipe.



      A103526
    1. Remove the 2 nuts and injection pipe clamp No.3.



    2. A103532
    3. Using SST, remove the 4 injection pipes.

      SST
      09023-12701  



12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A102463
  1. Using a small screwdriver, remove the holder seal by prying the portion between the holder seal and the cutout part of the cylinder head.

  1. Disconnect the ventilation hose.

  1. Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.

    NOTICE:
    After removing the fuel pipe, put a plastic bag and rubber band to prevent dirt and foreign objects over the injectors inlet.



13. SET NO.1 CYLINDER TO TDC/ COMPRESSION


    A072847E01
  1. Align the matchmarks of the crankshaft pulley and timing gear case cover by rotating the crankshaft in clockwise direction.

    HINT:
    Make sure that both camnoses on the intake side and exhaust side of the cylinder No.1 face upward.



14. REMOVE TIMING BELT


    A070549E01
  1. Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.



    A070550
  1. Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.

  1. Remove the timing belt.



15. REMOVE CAMSHAFT TIMING PULLEY


    A070695
  1. Remove the bolt for the camshaft timing pulley while holding the camshaft with a monkey wrench.



    A077212E01
  1. Using SST, remove the camshaft timing pulley.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061)



16. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1


    A070696
  1. Using a 10 mm socket hexagonal wrench remove the timing belt idler No.1.



17. REMOVE TIMING BELT NO.2 COVER


    A070697
  1. Remove the 4 bolts and nuts, then remove the timing belt No.2 cover.



18. REMOVE INJECTOR ASSEMBLY
(Click here)


19. REMOVE CAMSHAFT


    A070698
  1. Uniformly loosen and remove the 15 camshaft bearing cap bolts in the specified order described in the illustration.

  1. Remove the 5 camshaft bearing caps.

  1. Pull out the oil seal.



    A070699
  1. Remove the camshaft and No.2 camshaft.

    NOTICE:
    1. Do not pry the camshaft.
    2. Do not damage the thrusts of the cylinder head.