Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › ENGINE REAR OIL SEAL

ENGINE REAR OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE REAR OIL SEAL


    A072423E02
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09223-15030  
    09950-70010   (09951-07200)

    Acceptable depth from the top flat face of the oil seal retainer:
    0 to 0.5 mm (0 to 0.020 in.)

    NOTICE:
    Be sure to make the oil seal horizontal when embedded.

  1. Apply a bit of MP grease to the oil seal's lip.

    NOTICE:
    Keep the lip clean. Do not bring dirt or dusts on that area.



2. INSTALL ENGINE REAR OIL SEAL RETAINER


    A075507E02
  1. Remove oil seal packing (FIPG) from oil pan and cylinder block.

  1. Apply a seal packing to the specific places described in the illustration.

    Seal packing:
    Part No. 08826-00080 or equivalent

    NOTICE:
    1. After applying FIPG install the engine rear oil seal retainer within 3 minutes and then tighten its bolts within 15 minutes.
    2. Do not start the engine 2 hours after the installation.



    A072856E01
  1. Install the engine rear oil seal retainer with the 7 bolts.

    Torque:
    Bolt A:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
    Bolt B:
    16 N*m{ 166 kgf*cm , 12 ft.*lbf }



3. INSTALL REAR END PLATE
  1. Install the rear end plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL FLYWHEEL SUB-ASSEMBLY


    A072424E01
  1. Fix the crankshaft with SST.

    SST
    09213-58013  
    09330-00021  



    A054047
  1. Apply adhesive to 2 or 3 threads of the 8 bolts.

    Adhesive:
    Part No. 08833-00080, THREE BOND 1344, LOCTITE 242 or equivalent



    A102803E01
  1. For manual transmission

    1. Install the flywheel with the 8 bolts.

      Torque:
      178 N*m{ 1,815 kgf*cm , 131 ft.*lbf }

  1. For automatic transmission.

    1. Install the flywheel, drive plate and drive plate spacer rear with the 8 bolt.

      Torque:
      178 N*m{ 1,815 kgf*cm , 131 ft.*lbf }



5. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)


    C104159E01
  1. Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.



6. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)


    C114265E02
  1. Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Evenly tighten the bolts by following the order shown in the illustration.
    2. Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.



7. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)


    C086210
  1. Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    1.3 mm (0.051 in.)



    C114266E01
  1. If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

    SST
    09333-00013  



8. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


9. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)