FRONT DOOR > REASSEMBLY |
| 1. INSTALL FRONT DOOR WEATHER STRIP |
| 2. INSTALL FRONT DOOR CHECK ASSEMBLY |
![]() |
Install the front door check assembly with the 2 bolts.
![]() |
Install the bolt.
| 3. INSTALL FRONT NO.1 SPEAKER ASSEMBLY (w/ Speaker) |
![]() |
Using an air riveter or hand riveter, install 3 new strike rivets on the front No.1 speaker assembly on the front door panel.
![]() |
![]() |
![]() |
Connect the connector.
| 4. INSTALL SPEAKER COVER FRONT (w/o Speaker) |
Install the speaker cover front to the door.
Using a riveter, install the speaker cover front.

| 5. INSTALL FRONT DOOR SERVICE HOLE NO.2 COVER |
![]() |
Install the front door service hole No.2 cover with the 2 screws.
| 6. INSTALL FRONT DOOR LOCK ASSEMBLY |
Apply body grease to the sliding parts on the front door lock assembly.
![]() |
Install a new door lock wire harness.
Insert the front door outside handle link to the front door lock assembly, and set it to the front door panel.
Make sure that the front door outside handle link is securely connected to the front door lock assembly.
![]() |
Using a "torx" socket wrench (T30), install the front door outside handle lock assembly with the 3 "torx" screws.
| 7. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
| 8. INSTALL FRONT DOOR HANDLE ASSEMBLY OUTSIDE |
Using a "torx" socket wrench (T30), install the front door handle assembly outside with the "torx" screw.
| 9. INSTALL FRONT DOOR OUTSIDE HANDLE COVER |
![]() |
Using a "torx" socket wrench (T30), install the front door outside handle cover (with the door lock key cylinder installed) with the "torx" screw.
![]() |
Install the plug hole.
| 10. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER |
Install the front door frame sub-assembly rear lower with the bolt.
| 11. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 12. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY (w/ Power Window) |
Apply body grease to the sliding parts on the power window regulator motor.
![]() |
Using a "torx" socket wrench, install the power window regulator motor assembly with the 3 "torx" screws.
| 13. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window) |
Apply body grease to the sliding parts on the front door window regulator assembly.
![]() |
Install the front door window regulator assembly with the 6 bolts.
Connect the connector.
| 14. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window) |
![]() |
Apply body grease to the sliding parts on the front door window regulator assembly.
Install the front door window regulator assembly with the 6 bolts.
| 15. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY (w/ Power Window) |
![]() |
Connect the front door glass sub-assembly to the bracket on the front door window regulator assembly.
Install the front door glass with the 2 bolts.
Install the plug hole.
| 16. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY (w/o Power Window) |
![]() |
Connect the front door glass sub-assembly to the bracket on the front door window regulator assembly.
Install the front door glass with the 2 bolts.
Install the plug hole.
| 17. INSTALL FRONT DOOR GLASS WEATHER STRIP ASSEMBLY OUTER |
| 18. INSTALL FRONT DOOR SERVICE HOLE COVER |
Engage the clip.
![]() |
Install the front door service hole cover with the 6 bolts.
Engage the clamp and connect the connector.
| 19. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY (w/o Electric Mirror) |
![]() |
Install the outer rear view mirror with the 3 nuts.
| 20. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY (w/ Electric Mirror) |
![]() |
Install the outer rear view mirror with the 3 nuts.
Install the clamp.
Connect the connector.
| 21. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (w/ Power Window) |
![]() |
Engage the 12 clips and install the front door trim board sub-assembly with the screw.
| 22. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (w/o Power Window) |
![]() |
Engage the 12 clips and install the front door trim board sub-assembly with the 3 screws.
| 23. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Power Window) |
Connect the connector.
Engage the clips and claws and install the power window regulator master switch assembly with the 2 screws.
| 24. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
Temporarily install the front door window regulator handle assembly, and completely close the front door glass.
![]() |
Install the front door window regulator handle as shown in the illustration.
| 25. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Engage the 3 clips and install the front door lower frame bracket garnish.
| 26. INSPECT AND ADJUST FRONT DOOR |
| 27. RESET POWER WINDOW REGULATOR MOTOR (w/ Power Window) |