Home › BODY › ENGINE HOOD / DOOR › SLIDE DOOR

SLIDE DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL SLIDE DOOR ROLLER ASSEMBLY LOWER
  1. Install the slide door roller assembly lower with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



2. INSTALL SLIDE DOOR HINGE ASSEMBLY CENTER
  1. Install the slide door roller hinge assembly center with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



3. INSTALL SLIDE DOOR ROLLER ASSEMBLY UPPER
  1. Install the slide door roller assembly upper with the 2 bolts

    Torque:
    11.5 N*m{ 117 kgf*cm , 9 ft.*lbf }



4. INSTALL SLIDE DOOR SUB-ASSEMBLY


5. INSTALL SLIDE DOOR LOWER RAIL PLATE


    B106870
  1. Install the slide door lower rail plate with the bolt.



6. INSTALL SLIDE DOOR UPPER RAIL CUSHION


    B106867
  1. Install the slide door upper rail cushion with the bolt.



7. INSTALL SLIDE RAIL END MOULDING
  1. Engage the clip and install the slide rail end moulding.



8. INSTALL REAR DOOR SCUFF PLATE


    B111430
  1. Engage the clips, and install the rear door scuff plate.



9. INSTALL SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY


    B101184
  1. Install the slide door lock remote control assembly with the 5 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



10. INSTALL POWER SLIDE DOOR LOCK ASSEMBLY (w/ Auto Closer)


    B111441E01
  1. Using a "torx" socket wrench, install the 3 "torx" screws.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the bolt.

  1. Engage the wire harness and connect the cable.



11. INSTALL REAR DOOR LOCK ASSEMBLY (w/o Auto Closer)


    B111440E01
  1. Using a "torx" socket wrench, install the 3 "torx" screws.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage the wire harness and connect the cable.



12. INSTALL SLIDE DOOR CLOSER RELAY (w/ Auto Closer)


    B101181
  1. Install the slide door closer relay with the bolt.

  1. Connect the connector.



13. INSTALL SLIDE DOOR FULL OPEN STOP LOCK ASSEMBLY


    B111439E01
  1. Install the slide door full open stop lock assembly with the 2 bolts.

  1. Install the clamp.



14. INSTALL SLIDE DOOR DOWN FEMALE STOP


    B101179
  1. Install the slide door down female stop with the 2 bolts.



15. INSTALL SLIDE DOOR CONTROL JUNCTION FEMALE


    B101178E01
  1. Install the slide door control junction female with the 2 bolts.

  1. Connect the connector.



16. INSTALL SLIDE DOOR LOCK ASSEMBLY FRONT


    B111438E01
  1. Install the slide door lock assembly front with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Clamp the cable and install the end of the cable to the slide door lock remote control assembly front.



17. INSTALL REAR DOOR OPEN CONTROL LINK ASSEMBLY
  1. Install the rear door open control link assembly with the clip.



18. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B101175
  1. Install the rear door outside handle assembly with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the link.



    B102797
  1. Install the slide door lock cylinder assembly with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the link.



19. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
  1. Install the rear door inside handle sub-assembly with the 2 bolts.

  1. Connect the link.



20. INSTALL SLIDE DOOR SERVICE HOLE NO.1 COVER


21. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY (w/ Auto Closer)


    B101171E01
  1. Engage the clips and claw, and install the rear door trim board sub-assembly.



    B101169
  1. Using a "torx" socket wrench, install the 2 "torx" screws.



22. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY (w/o Auto Closer)


    B101170
  1. Install the rear door trim board sub-assembly with the 20 clips.



23. INSTALL SLIDE DOOR WINDOW GARNISH (w/ Auto Closer)


    B101167E01
  1. Engage the clips and install the slide door window garnish.



24. INSTALL DOOR LOCK CONTROL KNOB BEZEL (w/o Auto Closer)


    B101168E01
  1. Engage the claws and install the door lock control knob bezel.

  1. Using a "torx" socket wrench, install the 2 "torx" screws.



25. INSPECT AND ADJUST SLIDE DOOR
(Click here)