Home › BODY › ENGINE HOOD / DOOR › BACK DOOR

BACK DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL BACK DOOR STAY ASSEMBLY LH


    B102096
  1. Install the back door stay assembly LH with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



2. INSTALL BACK DOOR STAY ASSEMBLY RH

Torque:
22 N*m{ 224 kgf*cm , 16 ft.*lbf }



3. INSTALL BACK DOOR STOPPER LH


    B106855E02
  1. Install the back door stopper LH with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. INSTALL BACK DOOR STOPPER RH

Torque:
7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



5. INSTALL BACK DOOR LOCK ASSEMBLY


    B106864E01
  1. Install the back door lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



6. INSTALL BACK DOOR LOCK PROTECTOR (w/ Rear Bumper Step)


    B101156
  1. Install the back door lock protector with the screw.



7. INSTALL BACK DOOR STOPPER BRACKET SUB-ASSEMBLY (for Rough Road Area Spec.)


    B106856
  1. Install the back door stopper bracket sub-assembly with the 2 bolts.



8. INSTALL BACK DOOR NO.2 WIRE


    B111435E01
  1. Engage the clamps.

  1. Install the back door No.2 wire with the bolt.



9. INSTALL BACK DOOR NO.1 WIRE


10. INSTALL BACK DOOR GARNISH OUTSIDE


11. INSTALL BACK DOOR OUTSIDE HANDLE


    B101154
  1. Install the back door outside handle with the 2 nuts.



12. INSTALL BACK DOOR REMOTE CONTROL ASSEMBLY (w/o Power Door Lock)


    B111443E01
  1. Install the back door remote control assembly with the screw.

  1. Connect the wire and link.

  1. Engage the clamp.



13. INSTALL BACK DOOR REMOTE CONTROL ASSEMBLY (w/ Power Door Lock)


    B111442E01
  1. Install the back door remote control assembly with the 3 screws.

  1. Connect the wire and link.

  1. Engage the clamp.



14. INSTALL BACK DOOR INSIDE HANDLE ASSEMBLY (w/ Back Door Inside Handle)


  1. Install the back door inside handle assembly with the 3 screws.


    B111444E01

  1. Connect the link.



15. INSTALL BACK DOOR TRIM BOARD (DX Grade)


    B101152E01
  1. Engage the 18 clips and install the back door trim board.



16. INSTALL BACK DOOR TRIM BOARD (GL Grade)


    B101151
  1. Install the back door trim board with the 16 clips.



17. INSTALL BACK DOOR INSIDE HANDLE BEZEL (w/ Back Door Inside Handle Bezel)


    B101149
  1. Install the back door inside handle bezel with the 2 screws.



18. INSTALL BACK DOOR INSIDE HANDLE (w/ Back Door Inside Handle)


    B101148
  1. Install the back door inside handle with the screw.



19. INSTALL REAR WINDOW NO.1 WIRE


    B111432E01
  1. Engage the clamps and install the rear window No.1 wire.



20. INSTALL BACK DOOR NO.3 WIRE
  1. Pass the end of the back door wire into the cabin, and connect it to the connector.



    B111431E01
  1. Engage the clamps and install the back door No.3 wire.



21. INSTALL HIGH MOUNTED STOP LIGHT ASSEMBLY (w/ High Mounted Stop Light)


    E103126E01
  1. Install the high mounted stop light assembly with the 4 claws.

  1. Connect the connector.



22. INSTALL REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)


    E104706E01
  1. Install the grommet as shown in the illustration.



    E103138E01
  1. Install the rear wiper motor with the 3 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the clamp and connect the connector.



23. INSTALL REAR WIPER LINK PIVOT NO.1 WASHER (w/ Rear Wiper)


    E103141E02
  1. Install the rear No.1 wiper link pivot washer from the outside of the vehicle with the installation mark at the top.



    E103140
  1. Using the socket wrench (27 mm), install the lock nut.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not damage the glass.



24. INSTALL REAR WIPER SHAFT COVER (w/ Rear Wiper)


25. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)


    B108016E03
  1. Operate the wiper, and stop the rear wiper motor at the automatic stop position.

  1. Clean the wiper arm serrations.

  1. Clean the wiper pivot serrations with a wire brush (when reinstalling).



    E103534E01
  1. Install the rear wiper arm and blade assembly with the nut at the position as shown in the illustration.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    HINT:
    Hold the arm hinge by hand to fasten the nut.

  1. Operate the rear wiper while spraying water or washer fluid on the windshield. Make sure that the wipers function properly and there is no interference with the vehicle body.



26. INSTALL BACK DOOR TRIM BOARD ASSEMBLY UPPER (w/ Rear Wiper)


    B101147E01
  1. Engage the clips and install the back door trim board assembly upper.



27. INSTALL BACK DOOR TRIM BOARD ASSEMBLY UPPER (w/o Rear Wiper)


    B101146E01
  1. Engage the clips and install the back door trim board assembly upper.



28. INSTALL OUTER UNDER REAR VIEW MIRROR ASSEMBLY (w/o Outer Under Rear View Mirror)


    B102348E02
  1. Install the outer under rear view mirror with the 3 screws and the pin.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



29. INSPECT AND ADJUST BACK DOOR
(Click here)