Home › ENGINE ยท 5L-E › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY
  1. Install a new gasket, the water pump and tension spring bracket with the 6 bolts.

    Torque:
    23 N*m{ 230 kgf*cm , 17 ft.*lbf }



2. INSTALL TIMING BELT
SST
09960-10010   (09962-01000, 09963-01000)


3. SET NO.1 CYLINDER TO TDC/COMPRESSION


    A071316E01
  1. Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.

    NOTICE:
    Do not turn the crankshaft pulley counterclockwise.



    A071317E01
  1. Set the timing and drive pulleys at each position.

    NOTICE:
    1. The engine should be cold.
    2. When turning the crankshaft or camshaft, the valve heads will hit against the piston top. Do not turn them more than necessary.



4. INSTALL TIMING BELT GUIDE


    A058736E01
  1. Install the belt guide with the cup side facing outward.



5. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
  1. Remove the 2 nuts and wire harness clamp bracket.



    A112018E01
  1. Install the 2 gaskets to the timing belt cover.



    A112017
  1. Install the timing belt cover with the 11 bolts.

    Torque:
    11 N*m{ 105 kgf*cm , 8 ft.*lbf }

  1. Install the 2 nuts and wire harness clamp bracket.



6. INSTALL CRANKSHAFT PULLEY
SST
09213-54015   (91651-60855)
09330-00021  


7. INSTALL VANE PUMP PULLEY


    C106134E01
  1. Using SST, install the vane pump pulley to the vane pump assembly.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }



8. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning)
  1. Temporarily install the compressor mounting bracket with the 4 bolts.



    A112015E01
  1. Using several steps, uniformly install and tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }



    A112016
  1. Temporarily tighten the bolt and spacer.



    A112014E01
  1. Temporarily install the compressor mounting bracket with the 3 bolts.

  1. Using several steps, uniformly install and tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    47 N*m{ 475 kgf*cm , 36 ft.*lbf }



9. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning)


    E107314E01
  1. Install the compressor and magnetic clutch with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.



10. INSTALL FAN AND GENERATOR V BELT (w/o Air Conditioning)


    A115631E01
  1. Install the V belt.

  1. Using a bar, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



11. INSTALL FAN AND GENERATOR V BELT (w/ Air Conditioning)


    A115632E01
  1. Install the V belt.

  1. Tightening the bolt C, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



12. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1


    A074095E01
  1. Install the V belt.

  1. Tightening the bolt B, adjust the tension of the V belt.

  1. Tighten nut A.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



13. INSTALL VANE PUMP V BELT (w/ Air Conditioning)


    A071310E01
  1. Install the V belt.

  1. Using a bar, adjust the tension of the V-ribbed belt.

  1. Tighten the bolt A and nut B.

    Torque:
    Bolt (A):
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }
    Nut (B):
    64 N*m{ 635 kgf*cm , 47 ft.*lbf }

  1. Check the tension of the V belt. (Click here)



14. INSTALL WATER PUMP PULLEY


15. CONNECT RADIATOR HOSE NO.4


16. CONNECT RADIATOR HOSE INLET


17. ADD ENGINE COOLANT
  1. Close the engine drain plug.

    Torque:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }

  1. Close the radiator drain cock plug.

  1. Slowly fill the cooling system with coolant.

    HINT:
    The coolant level inside the radiator should be abserved after pressing the radiator hose inlet and radiator hose outlet by hand..

  1. Slowly pour coolant into the radiator reserve tank until it reaches the FULL line.

  1. Install the radiator cap to the radiator reserve tank.

  1. Press the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add coolant to the FULL line of the radiator reservoir.



18. START THE ENGINE


19. CHECK FOR ENGINE COOLANT LEAKS


20. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the 5 bolts and engine service hole cover.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



21. INSTALL FRONT DOOR SCUFF PLATE RH


22. INSTALL FRONT SEAT ASSEMBLY RH


    B107528
  1. Connect the front seat inner belt assembly connector and install the front seat assembly.

  1. Align the front seat assembly adjuster pin with the holes in the body.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the front side of the front seat assembly.

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }