ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT COOLANT |
| 2. INSPECT ENGINE OIL |
| 3. INSPECT BATTERY SPECIFIC GRAVITY |
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element from the air cleaner case sub-assembly.
Visually check that there is no dirt, clog, and damage to the air cleaner filter element.
| 5. INSPECT VANE PUMP V BELT |
![]() |
Check the V belt deflection.
Belt deflection
| New belt mm (in.) | Used belt mm (in.) |
| 7.5 to 9.5 (0.30 to 0.37) | 9.0 to 13 (0.35 to 0.51) |
Tension
| New belt N (kgf) | Used belt N (kgf) |
| 441 to 539 (45 to 55) | 245 to 343 (25 to 35) |
| 6. INSPECT V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (W/ AIR CONDITIONING) |
![]() |
Check the V belt deflection.
Belt deflection
| New belt mm (in.) | Used belt mm (in.) |
| 11 to 15 (0.43 to 0.59) | 15 to 20 (0.59 to 0.79) |
Tension
| New belt N (kgf) | Used belt N (kgf) |
| 372 to 608 (38 to 62) | 196 to 392 (20 to 40) |
| 7. INSPECT FAN AND GENERATOR V BELT |
![]() |
Check the V belt deflection. (Per 1 belt)
Belt deflection
| New belt mm (in.) | Used belt mm (in.) |
| 7.0 to 10 (0.28 to 0.39) | 10 to 14 (0.39 to 0.55) |
Tension (Per 1 belt)
| New belt N (kgf) | Used belt N (kgf) |
| 441 to 539 (45 to 55) | 196 to 343 (20 to 35) |
| 8. INSPECT INJECTION TIMING |
![]() |
Using a mirror, check that the matchmarks of the injection pump flange and the timing gear case are aligned.
| 9. ADJUST INJECTION TIMING |
![]() |
Loosen the following nuts and bolts.
Bolt holding the injection pump to the injection pump stay.
2 nuts holding the injection pump to the timing gear case.
Align the matchmark by slightly tilting the injection pump.
Tighten the following nuts and bolts.
2 nuts holding the injection pump to the timing gear case.
Bolt holding the injection pump to the injection pump stay.
| 10. INSPECT ENGINE IDLE SPEED |
Warm up the engine.
When using an intelligent tester:
Connect the intelligent tester to the DLC3.
![]() |
When not using an intelligent tester:
Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.
Check the idle speed.
| 11. INSPECT MAXIMUM ENGINE SPEED |
Start the engine.
Depress the accelerator pedal all the way.
Check the maximum speed.
| 12. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove the glow plugs. (Click here)
Disconnect the spill control valve connector.
Check the cylinder compression pressure.
![]() |
Install SST (attachment) to the glow plug hole.
![]() |
Connect SST (compression gauge) to the SST (attachment).
Fully open the throttle valve, and start the engine.
While cranking the engine, measure the compression pressure.
Repeat steps (a) through (d) for each cylinder.
If the cylinder compression in one or more cylinders is low, pour a small amount of engine oil into the cylinder through the glow plug hole and repeat steps (a) through (d) for the cylinder with low compression.
If adding oil helps the compression, the piston rings and/or cylinder bore may be worn or damaged.
If pressure stays low, a valve may be stuck or the seating may be improper, or there may be leakage past the gasket.
Remove the SST.
Reinstall the glow plugs. (Click here)
Reconnect the spill control valve connector.