GLOW PLUG > REMOVAL |
| 1. DISCONNECT NEGATIVE BATTERY CABLE |
| 2. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type) |
Perform the same procedure as above on the opposite side. (Click here)
| 3. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type) |
Perform the same procedure as above on the opposite side. (Click here)
| 4. REMOVE FRONT DOOR SCUFF PLATE RH |
| 5. REMOVE ENGINE SERVICE HOLE SUB COVER ASSEMBLY |
Roll up the carpet, and remove the engine service hole sub cover assembly.
| 6. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY |
![]() |
Remove the 2 bolts and vane pump oil reservoir assembly.
| 7. DISCONNECT OIL RETURN HOSE (w/ Inter cooler) |
![]() |
Loosen the clip.
Disconnect the oil return hose from the intake manifold.
| 8. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve) |
![]() |
Disconnect the fuel pressure sensor connector.
![]() |
Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.
Remove the 2 gaskets.
| 9. REMOVE AIR HOSE NO.4 |
![]() |
Loosen the 2 clamps.
Remove the air hose No.4.
| 10. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
![]() |
Disconnect the 2 throttle body connectors.
![]() |
Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.
Remove the gasket from intake air connector.
| 11. REMOVE ENGINE SERVICE HOLE COVER NO.2 |
![]() |
Roll up the carpet.
Remove the 3 bolts and the engine service hole cover No.2.
| 12. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve) |
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from intake air connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and intake air connector No.2 from the intake air connector.
| 13. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve) |
Remove the vacuum regulating valve.
![]() |
Remove the 2 vacuum hoses and the vacuum regulating valve connector.
Remove the 2 bolts and the vacuum regulating valve.
Remove the EGR valve assembly with the sensor.
![]() |
Remove the bolt, and separate the manifold stay.
Disconnect the vacuum hose from the intake air connector.
![]() |
Disconnect the intake air temperature sensor connector.
Disconnect the EGR valve position sensor connector.
![]() |
Remove the bolt, 2 nuts and the intake air connector assembly.
Remove the 2 gaskets and EGR valve assembly from the intake air connector.
| 14. REMOVE OIL LEVEL GAUGE GUIDE |
Remove the oil level gauge.
Remove the bolt and oil level gauge guide.
| 15. REMOVE INJECTION PIPE |
Remove the injection pipe.
![]() |
Remove the 2 nuts and injection pipe clamp No.3.
![]() |
Using SST, remove the 4 injection pipes.
| 16. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
Using SST, remove the fuel inlet pipe sub-assembly.
| 17. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY NO.2 |
![]() |
Remove the union bolt and gasket.
![]() |
Remove the 2 bolts and the nozzle leakage pipe assembly No.2.
| 18. REMOVE INTAKE MANIFOLD |
Remove the bolt, nut, and the manifold stay.
Remove the bolt, and disconnect the ground cable.
![]() |
Remove the 4 bolts, 2 nuts, and intake manifold.
Remove the gasket from the cylinder head.
| 19. REMOVE GLOW PLUG NO.1 CONNECTOR |
Remove the 4 grommets.
Remove the 4 nuts and glow plug No.1 connectors.
| 20. REMOVE GLOW PLUG |
Using a deep socket wrench (12 mm), remove the 4 glow plugs.