Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD

INSTRUMENT PANEL SAFETY PAD > INSTALLATION

for Preparation Click here



1. INSTALL INSTRUMENT PANEL ASSEMBLY
  1. Connect the all connectors.



  1. Install the instrument panel assembly with the 4 bolts <A>, 2 screws <B> and 2 nuts <D>.


    B102835E01



2. INSTALL FRONT PILLAR GARNISH RH


3. INSTALL FRONT PILLAR GARNISH LH


4. INSTALL ASSIST GRIP ASSEMBLY


5. INSTALL FRONT ASSIST GRIP NO.1 PLUG


6. INSTALL HAZARD WARNING SIGNAL SWITCH ASSEMBLY


7. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)
  1. Engage the clamps and claws, and install the front passenger airbag assembly.



    C106066
  1. Install the instrument panel passenger airbag with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



    C106065E02
  1. Connect the airbag connector.

  1. Install the airbag connector to the reinforcement.



8. INSTALL AIR CONDITIONER PANEL SUB-ASSEMBLY


    E108139
  1. Install the heater control base with the 2 screws.



    E108771E01
  1. Engage the 2 claws to install the defroster damper control cable sub-assembly.



    E108770E01
  1. Engage the 2 claws to install the boost ventilator control cable sub-assembly.

  1. Install the clamp.

  1. Install the connector.



    E108769E01
  1. Engage the 9 clips to install the air conditioner panel sub-assembly.



9. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY (for Automatic Transmission)
For 2KD-FTV
For 2TR-FE


10. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY (for Manual Transmission)
For 5L-E
For 2KD-FTV, 2TR-FE


11. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


12. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    B102832E01
  1. Engage the 8 claws and install the instrument panel finish panel lower center.



13. INSTALL SHIFTING HOLE COVER ASSEMBLY


    B102831E01
  1. Manual Transmission:
    Engage the 6 claws and install the shifting hole cover assembly.

  1. Automatic Transmission:
    Engage the 8 claws and install the sifting hole cover assembly.



14. INSTALL SHIFT LEVER KNOB


15. INSTALL PARKING BRAKE HOLE COVER


    B102829E01
  1. Engage the 6 claws and install the parking brake hole cover.



16. INSTALL INSTRUMENT PANEL NO.1 UNDER COVER SUB-ASSEMBLY


    B102828E01
  1. Engage the 3 claws.

  1. Install the instrument panel No.1 under cover sub-assembly with the 2 clips.



17. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    B102827E01
  1. Engage the 4 clips (B).

  1. Install the instrument panel finish panel lower with the 2 clips (A).



18. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


19. INSTALL STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    B102826
  1. Install the radio tuner opening cover with bracket with the 4 screws <C>.



20. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    B102825
  1. Install the instrument panel cup holder assembly with the 3 screws <C>.



21. INSTALL COMBINATION METER ASSEMBLY


    B106891E01
  1. Connect the connector and engage the 2 claws.



    B102823
  1. Install the combination meter assembly with the 2 screws <B>.



22. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Engage the 6 claws and install the instrument cluster finish panel sub-assembly.



23. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


24. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 GARNISH


25. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER


26. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.2 GARNISH


27. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY
  1. Install the wiper switch with the claw.

    HINT:
    Slide the steering column cover upper upward to install the wiper switch.

  1. Connect the connector.



28. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Install the headlight dimmer switch with the claw.

    HINT:
    Slide the steering column upper cover upward to install the headlight dimmer switch.

  1. Connect the connector.



29. INSTALL STEERING COLUMN COVER UPPER


30. INSTALL KEY CYLINDER LIGHT ASSEMBLY (w/ Key Cylinder Light)


31. INSTALL STEERING COLUMN COVER LOWER


    C102128
  1. Engage the 3 claws to install the steering column cover upper and lower with the 2 "torx" screws.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }



32. ADJUST SPIRAL CABLE SUB-ASSEMBLY (w/ SRS Airbag)
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    After removing the terminal, wait for at least 90 seconds before starting the operation.



    C106055
  1. Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable with steering sensor by the airbag wire harness.



    C106056
  1. Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



33. INSTALL STEERING WHEEL ASSEMBLY


    C106050E01
  1. w/o AIRBAG:

    1. Position the horn contact plate so that the projecting parts are as shown the illustration.

  1. Align the matchmarks on the steering wheel assembly and the steering column assembly.

  1. Install the nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors.



34. INSTALL STEERING PAD (w/o SRS Airbag)
  1. Connect the horn connector.



    C106047E01
  1. Install the steering pad with the screw.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf }



35. INSTALL STEERING PAD (w/ SRS Airbag)
  1. Support the steering pad with one hand.



    C106059
  1. Connect the connector to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the circumference groove of the "torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.



    C106057E02
  1. Using a "torx" socket wrench (T30), tighten the 2 "torx" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



36. INSTALL STEERING WHEEL NO.3 COVER LOWER


37. INSTALL STEERING WHEEL NO.2 COVER LOWER


38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


39. PERFORM INITIALIZATION

NOTICE:
Some systems need initialization when disconnecting the cable from the negative (-) battery terminal (Click here).



40. INSPECT STEERING PAD (w/ SRS Airbag)
  1. Perform a diagnostic system check. (Click here)



    C116332
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.



41. INSPECT SRS WARNING LIGHT (w/ SRS Airbag)
(Click here)