STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSTALL WIPER SWITCH |
Install the wiper switch with the claw.
Connect the connector.
| 2. INSTALL HEADLIGHT DIMMER SWITCH |
Install the headlight dimmer switch with the claw.
Connect the connector.
| 3. INSTALL SPIRAL CABLE ASSEMBLY (W/ AIRBAG) |
Check that the front wheels are facing straight ahead.
Set the turn signal switch to the neutral position.
![]() |
Engage the 3 claws and install the spiral cable with steering sensor.
Connect the connectors to the spiral cable with steering sensor.
| 4. INSTALL STEERING COLUMN COVER UPPER |
| 5. INSTALL HORN CONTACT PLATE (W/O AIRBAG) |
![]() |
Engage the 2 claws and install the horn contact plate.
Connect the connector.
| 6. INSTALL STEERING INTERMEDIATE SHAFT |
Align the matchmarks on the steering intermediate shaft assembly No.2 and the steering gear assembly.
![]() |
Temporarily install the bolt.
| 7. INSTALL STEERING COLUMN ASSEMBLY |
Temporarily install the steering column assembly with the 3 bolts.

Fully tighten the 3 bolts on the steering column assembly.
Fully tighten the bolt on the steering intermediate shaft assembly No.2.
Connect the connectors and clamp the wire harness to the steering column assembly bracket.
![]() |
Install the steering shaft cover with the 3 bolts.
| 8. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER |
![]() |
Engage the 4 clips (B).
Install the instrument panel finish panel lower with the 2 clips (A).
| 9. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 10. CENTER SPIRAL CABLE (W/ AIRBAG) |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.
![]() |
Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.
| 11. INSTALL STEERING COLUMN COVER LOWER |
![]() |
Engage the 3 claws to install the steering column cover upper and lower with the 2 "torx" screws.
| 12. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
w/o AIRBAG:
Position the horn contact plate so that the projecting parts are as shown the illustration.
Align the matchmarks on the steering wheel assembly and the steering column assembly.
Install the nut.
Connect the connectors.
| 13. INSPECT STEERING WHEEL CENTER POINT |
| 14. INSTALL STEERING PAD (W/ AIRBAG) |
Support the steering pad with one hand.
![]() |
Connect the connector to the steering pad.
Connect the horn connector.
Confirm that the circumference groove of the "torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
![]() |
Using a "torx" socket wrench (T30), tighten the 2 "torx" screws.
| 15. INSTALL STEERING WHEEL COVER LOWER NO.3 (W/ AIRBAG) |
Install the steering wheel cover lower No.3.
| 16. INSTALL STEERING WHEEL COVER LOWER NO.2 (W/ AIRBAG) |
Install the steering wheel cover lower No.2.
| 17. INSPECT STEERING PAD (W/ AIRBAG) |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 18. INSTALL STEERING PAD (W/O AIRBAG) |
Connect the horn connector.
![]() |
Install the steering pad with the screw.
| 19. CONNECT CABLE TO BATTERY NEGATIVE TERMINAL |
| 20. INSPECT SUPPLEMENTAL RESTRAINT SYSTEM WARNING LIGHT |
| 21. PERFORM INITIALIZATION |