ECD SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect an intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the intelligent tester on.
Select the following menu items: Powertrain/Engine and ECT/Data List.
Check the values by referring to the following table.
| Intelligent Tester Display (Abbreviation) | Measurement Item: Range (Display) | Normal Conditions * | Diagnostic Notes |
| Coolant Temp (COOLANT TEMP) | Engine coolant temperature: Min.: -40°C, Max.: 215°C | 80 to 95°C (176 to 203°F): After warming up engine | If value -40°C or 140°C, sensor circuit open or shorted |
| PIM (PIM) | Absolute pressure inside intake manifold: Min.: 0 kPa, Max.: 255 kPa |
| - |
| Engine SPD (ENGINE SPD) | Engine speed: Min.: 0 rpm, Max.: 16383.75 rpm | 720 to 820 rpm: Idling (A/C off) After warming up engine | - |
| Vehicle SPD (VEHICLE SPD) | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h | Actual vehicle speed | Speed indicated on speedometer |
| Intake Air (INTAKE AIR) | Intake air temperature: Min.: -40°C, Max.: 215°C | Equivalent to temperature at intake manifold | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Injection Volume (INJ VOLUME) | Injection volume: Min.: 0 mm3, Max.: 1279.98 mm3 | 3 to 11 mm3: Idling | - |
| Injection Timing (INJ TIMING) | Injection timing: Min.: 0 CA, Max.: 51 CA | 16 to 20 CA: Idling After warming up engine | - |
| Fuel Temp. (FUEL TEMP) | Fuel temperature status: Min.: -40°C, Max.: 215°C | Actual fuel temperature | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Accel Position (ACCEL POSITION) | Accelerator position status: Min.: 0 %, Max.: 100 % |
| Read value with engine switch ON (Do not start engine) |
| Throttle Step POS (THROTTLE POS) | Throttle step position: Min.: 1 step, Max.: 255 step |
| Read value with engine switch ON (Do not start engine) |
| #Codes (#CODES) | Number of memorized DTC codes: Min.: 0, Max.: 255 | 0 | - |
| Stop Light SW (STOP LIGHT SW) | Stop light switch: ON or OFF |
| - |
| A/C Signal (A/C SIGNAL) | A/C signal: ON or OFF | ON: A/C switch is turned ON | - |
| Starter SIG (STARTER SIG) | Starter signal: ON or OFF | ON: Cranking | - |
| Accel Open SW (ACCEL OPEN SW) | Accelerator pedal open switch: ON or OFF | ON: Ignition Switch ON | - |
| SPD Test (SPD Test) | Check mode result for vehicle speed sensor: 0: COMPL, 1: INCOMPL | - | Click here
|
| Check Mode (CHECK MODE) | Check mode: ON or OFF | ON: Check mode ON | - |
| A/C Cut SIG (A/C CUT SIG) | A/C cut signal: ON or OFF | ON: A/C compressor ON | - |
| ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the intelligent tester on.
Select the following menu items: Powertrain/Engine and ECT/Active Test.
Perform the Active Tests by referring to the following table.
| Intelligent Tester Display (Abbreviation) | Test Details | Control Range | Diagnostic Notes |
| Control the A/C cut signal (A/C CUT SIG) | Control A/C cut signal | ON/OFF | - |