DTC P0171 System Too Lean (Fuel Trim) |
DTC P0172 System Too Rich (Fuel Trim) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0171 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|
| P0172 | With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic) |
|

| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 (HO2) | +25 % | Rich | More than 0.5 |
| O2S B1S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Mainly Suspected Trouble Areas | ||
| 1 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() | - |
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 2 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 3 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 AND P0172) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0171 or P0172 | A |
| P0171 or P0172 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE |
|
| ||||
| OK | |
| 3.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (A/F CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester ON.
Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / A/F Control.
Perform the A/F Control operation with the engine in an idling condition.
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 (HO2) | +25 % | Rich | More than 0.5 |
| O2S B1S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Status AFS B1S1 | Status O2S B1S2 | A/F Condition and A/F Sensor Condition | Misfires | Suspected Trouble Areas | Proceed To |
| Lean/Rich | Lean/Rich | Normal | - | - | C |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| A |
| Lean | Lean/Rich | A/F sensor malfunction | - |
| B |
| Rich | Lean/Rich | A/F sensor malfunction | - |
| B |
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE OF INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 6.READ VALUE OF INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.
Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.
Read the MAF with the engine in an idling condition and at an engine speed of 2,500 rpm.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure.
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAKAGE |
|
| ||||
| OK | |
| 9.CHECK SPARK AND IGNITION |
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
|
| ||||
| OK | |
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the D33 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connections | Specified Conditions |
| HA1A (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 12.INSPECT INTEGRATION RELAY (A/F HEATER RELAY) |
Remove the integration relay from the engine room R/B No.1.
![]() |
Measure the integration relay (A/F HEATER relay) resistance.
| Tester Connections | Specified Conditions |
| A1 - C4 | 10 kΩ or higher |
| A1 - C4 | Below 1 Ω (when battery voltage applied to terminals C2 and C3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the D33 A/F sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (D33-2) - Body ground | 9 to 14 V |
Turn the ignition switch to OFF.
Disconnect the D1 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HA1A (D33-1) - HA1A (D1-1) | Below 1 Ω |
| A1A+ (D33-3) - A1A+ (D1-21) | Below 1 Ω |
| A1A- (D33-4) - A1A- (D1-31) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HA1A (D33-1) or HA1A (D1-1) - Body ground | 10 kΩ or higher |
| A1A+ (D33-3) or A1A+ (D1-21) - Body ground | 10 kΩ or higher |
| A1A- (D33-4) or A1A- (D1-31) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 15.PERFORM CONFIRMATION DRIVING PATTERN |

Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester ON.
Clear DTCs (Click here).
Switch the ECM from normal mode to check mode using the tester (Click here).
Start the engine and warm it up with all the accessories switched OFF.
Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1,400 rpm and 3,200 rpm for 3 to 5 minutes.
| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172) |
On the intelligent tester, select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| No output | A |
| P0171 or P0172 | B |
|
| ||||
| A | ||
| ||