DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Conditions | Trouble Area |
| P2195 |
|
|
| P2195 | While fuel-cut operation performed (during vehicle deceleration), Air-fuel Ratio (A/F) sensor current 3.6 mA or more for 3 seconds. (2 trip detection logic) |
|
| P2196 |
|
|
| While fuel-cut operation performed (during vehicle deceleration), Air-fuel Ratio (A/F) sensor current less than 1.0 mA for 3 seconds. (2 trip detection logic) |
|




| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 (A/F) | +25 % | Rich | Less than 3.0 |
| AFS B1S1 (A/F) | -12.5 % | Lean | More than 3.35 |
| O2S B1S2 (HO2) | +25 % | Rich | More than 0.5 |
| O2S B1S2 (HO2) | -12.5 % | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Mainly Suspected Trouble Areas | ||
| 1 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() | - |
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 2 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage More than 0.5 V Less than 0.4 V | ![]() | ||
| 3 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage More than 3.35 V Less than 3.0 V | ![]() | Output voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection volume +25 % -12.5 % | ![]() |
|
| Output voltage Almost no reaction | ![]() | Output voltage Almost no reaction | ![]() | ||
| 1.CHECK OTHER DTC OUTPUT (BESIDE A/F SENSOR DTC) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P2195 or P2196 | A |
| P2195 or P2196 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the Intelligent Tester to the DLC3.
Warm up the A/F sensor at 2,500 rpm for approximately 90 seconds.
Read A/F sensor voltage output on the intelligent tester.
Select "Powertrain / Engine and ECT / Data List / AFS B1S1 and Engine Spd.
Monitor the A/F sensor voltage carefully.
Check the A/F sensor voltage under the condition as follows:
Allow engine to idle for 30 seconds.
Engine is racing at approx. 2,500 rpm (when engine revolution is not suddenly changed).
Raise the engine speed to 4,000 rpm and release the fully closed accelerator pedal quickly.

|
| ||||
| NG | |
| 3.INSPECT AIR FUEL RATIO SENSOR |
![]() |
Disconnect the D33 Air-Fuel Ratio (A/F) sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connections | Specified Conditions |
| HA1A (1) - +B (2) | 1.8 Ω to 3.4 Ω at 20 °C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 4.INSPECT INTEGRATION RELAY (A/F HEATER RELAY) |
Remove the integration relay from the engine room R/B No.1.
![]() |
Check the integration relay (A/F HEATER relay).
| Tester Connections | Specified Conditions |
| A1 - C4 | 10 kΩ or higher |
| A1 - C4 | Below 1 Ω (when battery voltage applied to terminals C2 and C3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM) |
![]() |
Disconnect the D33 air-fuel ratio sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the +B terminal of the air-fuel ratio sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (D33-2) - Body ground | 9 to 14 V |
Turn the ignition switch to OFF.
Disconnect the D1 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HA1A (D33-1) - HA1A (D1-1) | Below 1 Ω |
| A1A+ (D33-3) - A1A+ (D1-21) | Below 1 Ω |
| A1A- (D33-4) - A1A- (D1-31) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HA1A (D33-1) or HA1A (D1-1) - Body ground | 10 kΩ or higher |
| A1A+ (D33-3) or A1A+ (D1-21) - Body ground | 10 kΩ or higher |
| A1A- (D33-4) or A1A- (D1-31) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the air-fuel ratio sensor connector.

|
| ||||
| OK | |
| 6.CHECK AIR INDUCTION SYSTEM |
Check for vacuum leaks in the air induction system.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check fuel pressure (High or low fuel pressure).
|
| ||||
| OK | |
| 8.INSPECT FUEL INJECTION ASSEMBLY |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).
|
| ||||
| OK | |
| 9.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 10.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 11.READ OUTPUT DTC (A/F SENSOR DTC OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester ON.
On the intelligent tester, select the following items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display | Proceed To |
| No output | A |
| P2195 or P2196 | B |
|
| ||||
| A | |
| 12.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
|
| ||||
| YES | ||
| ||
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 14.READ OUTPUT DTC (A/F SENSOR DTC OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester ON.
On the intelligent tester, select the following items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display | Proceed To |
| No output | A |
| P2195 or P2196 | B |
|
| ||||
| A | |
| 15.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 17.READ OUTPUT DTC (A/F SENSOR DTC OUTPUT AGAIN) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester ON.
On the intelligent tester, select the following items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display | Proceed To |
| No output | A |
| P2195 or P2196 | B |
|
| ||||
| A | |
| 18.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
|
| ||||
| YES | ||
| ||