Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/ Secondary Air Injection System)

DTC    P0418    Secondary Air Injection System Control "A" Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 (Click here).

DTC No.
DTC Detection Condition
Trouble Area
P0418
  1. After cold engine starts, all of following conditions are met
    (1 trip detection logic):
    1. Air Injection (AI) system not operate (air pump OFF, Air Switch Valve (ASV) OFF)
    2. Diagnostic signal from Air Injection Control Driver (AID) 20 %
    3. Battery voltage 8 V or more
  1. Open in air pump drive circuit
  2. Short between air pump circuit and +B circuit
  3. Air pump
  4. AID
  5. ECM
  1. After cold engine starts, all of following conditions are met
    (1 trip detection logic):
    1. While Air Injection (AI) system operating (air pump ON, Air Switching Valve (ASV) ON)
    2. Diagnostic signal from Air Injection Control Driver (AID) 20%
    3. Battery voltage 8 V or more
  1. Short between air pump circuit and body ground
  2. Air pump
  3. AID
  4. ECM

MONITOR DESCRIPTION

Air Injection Control Driver (AID) detects an open or short in the air pump and Air Switching Valve (ASV) circuit according to the terminal voltage and sends a signal as the diagnostic information to the ECM.
After the cold engine starts, the ECM transmits command signals to the AID to the drive the air pump and ASV.
The AID outputs the ASV malfunction signal to the ECM if: 1) the voltage of AID terminal for air pump is low despite the AID receiving the command signal from the ECM to drive the ASV or 2) VP terminal voltage is high despite the AID not receiving the command signal from the ECM.
The ECM sets the DTC based on the diagnostic signal from the AID.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

HINT:
The diagnostic information output from AID can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the AID.


  1. A065741E06
    Connect the intelligent tester to the DLC3.
  2. Connect an oscilloscope probe to the AIDI terminal of the ECM.
  3. Start the engine and turn the tester ON.

  4. Monitor the voltage output of the AID (duty ratio signal).

    Oscilloscope range: 
    Items
    Contents
    Terminals
    CH1: AIDI (D3-20) - E1 (D1-3)
    Equipment Settings
    5 V/Division, 20 to 40 ms/Division
    Conditions
    Idling


    A111145E02



    A111146E02

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT AIR PUMP ASSEMBLY


    G037120E01
  1. Disconnect the B17 air pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    Air pump (B17-1) - Air pump (B17-2)
    0.4 to 1.0 Ω

  1. Reconnect the air pump connector.



NG
REPLACE AIR PUMP ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - BODY GROUND)


    G037119E01
  1. Disconnect the B17 air pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    Air pump (B17-1) - Body ground
    Below 1 Ω

  1. Reconnect the air pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AIR INJECTION CONTROL)


    A110498E01
  1. Disconnect the B14 AID connector.

  1. Disconnect the B17 air pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    Air pump (B17-2) - VP (B14-2)
    Below 1 Ω

  1. Reconnect the air pump connector.

  1. Reconnect the AID connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR INJECTION CONTROL DRIVER