Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM (w/o Secondary Air Injection System)

SFI SYSTEM (w/o Secondary Air Injection System) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
By reading the Data List displayed on the intelligent tester, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect an intelligent tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn the intelligent tester ON.

  6. Select the following menu items: Powertrain / Engine and ECT / Data List.

  7. Check the values by referring to the table below.

    Intelligent Tester
    (Abbreviation)
    Measure Item/Range
    Normal Condition*
    Diagnostic Note
    Injector
    Injection period of No.1 cylinder/
    Min.: 0 ms, Max.: 32.64 ms
    1.8 to 3.8 ms: Idling
    -
    IGN Advance
    (Ign Advance)
    Ignition timing advance for No.1 cylinder/
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 4 to 17°: Idling
    -
    Calculate Load
    (Calc Load)
    Calculated load by ECM/
    Min.: 0 %, Max.: 100 %
    1. 11 to 26 %: Idling
    2. 12 to 27 %: Running without load (2,500 rpm)
    -
    MAF
    Air flow rate from MAF meter/ Min.: 0 g/s, Max.: 655.35 g/s
    2.0 to 4.5 g/s: Idling
    1. If value approximately 0.0 g/s:
      1. Mass air flow meter power source circuit open
    2. VG circuit open or short if value 160.0 g/s or more:
      1. E2G circuit open
    Engine Speed
    (Engine Spd)
    Engine speed/
    Min.: 0 rpm, Max.: 16,383.75 rpm
    600 to 700 rpm: Idling
    -
    Vehicle Speed
    (Vehicle Spd)
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    80 to 100°C (176 to 212°F):
    After warming up
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Intake Air
    Intake air temperature/ Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Air-Fuel Ratio*2
    Air-fuel ratio/
    Min.: 0, Max.: 1.999
    0.8 to 1.2: Idling
    -
    Purge Density Learn Value*2
    (Purge Density)
    Learning value of purge density/
    Min.: -50, Max.: 350
    -40 to 0 %: Idling
    Service data
    Purge Flow*2
    Purge flow/ Min.: 0 %, Max.: 102.4 %
    0 to 100 %: Idling
    -
    Knock Correct Learn Value
    (Knock Crrt Val)
    Correction learning value of knocking/
    Min.: -64 CA, Max.: 1,984 CA
    0 to 19 CA:
    Driving, 70 km/h (44 mph)
    Service data
    Knock Feedback Value
    (Knock FB Val)
    Feedback value of knocking/
    Min.: -64 CA, Max.: 1,984 CA
    -19 to 0 CA:
    Driving, 70 km/h (44 mph)
    Service data
    Accelerator Position No.1
    (Accel Pos #1)
    Absolute Accelerator Pedal Position (APP) No.1/
    Min.: 0 %, Max.: 100 %
    10 to 22 %: Accelerator pedal released
    54 to 86 %: Accelerator pedal fully depressed
    -
    Accelerator Position No.2
    (Accel Pos #2)
    Absolute APP No.2/
    Min.: 0 %, Max.: 100 %
    12 to 42 %: Accelerator pedal released
    66 to 98 %: Accelerator pedal fully depressed
    -
    Accelerator Position No.1
    (Accel Pos #1)
    APP sensor No.1 voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Accelerator Position No.2
    (Accel Pos #2)
    APP sensor No.2 voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Accelerator Position No.1
    (Accel Pos #1)
    APP sensor No.1 voltage/
    Min.: 0 V, Max.: 5 V
    0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed
    -
    Accelerator Position No.2
    (Accel Pos #2)
    APP sensor No.2 voltage/
    Min.: 0 V, Max.: 5 V
    1.2 to 2.0 V: Accelerator pedal released
    3.4 to 5.3 V: Accelerator pedal fully depressed
    -
    Accelerator Idle Position
    (Accel Idl Pos)
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Fully Close Learn
    (Thrtl Learn Val)
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 5 V
    0.4 to 0.8 V
    -
    Accel Fully Close #1 (AD)
    (Accel Ssr #1 AD)
    Accelerator fully closed value No.1 (AD)/
    Min.: 0 V, Max.: 4.9804 V
    -
    ETCS freeze data
    Accel Fully Close Learn #1
    (Accel Lrn Val#1)
    Accelerator fully closed learning value No.1/
    Min.: 0, Max.: 124.512
    -
    ETCS freeze data
    Accel Fully Close Learn #2
    (Accel Lrn Val#2)
    Accelerator fully closed learning value No.2/
    Min.: 0, Max.: 124.512
    -
    ETCS freeze data
    Fail Safe Drive
    (Fail #1)
    Whether or not fail safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    Fail Safe Drive (Main CPU)
    (Fail #2)
    Whether or not fail safe function executed/
    ON or OFF
    ON: ETCS has failed
    -
    ST1
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    System Guard
    (Sys Guard Judge)
    System guard:
    ON or OFF
    -
    ETCS freeze data
    Open Side Malfunction
    (Opn Malfunction)
    Open side malfunction/
    ON or OFF
    -
    ETCS freeze data
    Throttle Position
    (Throttle Pos)
    Absolute throttle position sensor/
    Min.: 0 %, Max.: 100%
    1. 10 to 24 %: Throttle fully closed
    2. 64 to 96 %: Throttle fully open
    -
    Throttle Idle Position
    (Throttl Idl Pos)
    Whether or not throttle position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Throttle Require Position
    (Thrtl Req Pos)
    Throttle requirement position/
    Min.: 0 V, Max.: 5 V
    0.5 to 1.0 V: Idling
    -
    Throttle Sensor Position
    (Throttle Pos)
    Throttle sensor positioning/
    Min.: 0 %, Max.: 100%
    10 to 18 %: Idling
    Calculated value based on VTA1
    Throttle Sensor Position #2
    (Throttle Pos #2)
    Throttle sensor positioning #2/
    Min.: 0 %, Max.: 100%
    -
    Calculated value based on VTA2
    Throttle Position No.1
    (Throttle Pos #1)
    Throttle position sensor No.1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Throttle Position No.2
    (Throttle Pos #2)
    Throttle position sensor No.2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze data
    Throttle Position No.1
    (Throttle Pos #1)
    Throttle position No.1/
    Min.: 0 V, Max.: 5 V
    1. 0.5 to 1.2 V: Throttle fully closed
    2. 3.2 to 4.8 V: Throttle fully open
    -
    Throttle Position No.2
    (Throttle Pos #2)
    Throttle position No.2/
    Min.: 0 V, Max.: 5 V
    1. 2.0 to 2.9 V: Throttle fully closed
    2. 4.6 to 5.5 V: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Position Command
    (Thrtl Comnd Val)
    Throttle position command value/
    Min.: 0 V, Max.: 4.9804 V
    0.5 to 4.8 V
    ETCS freeze data
    Throttle Sens Open Pos #1
    (Throttle Ssr #1)
    Throttle sensor opener position No.1/
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS freeze data
    Throttle Sens Open Pos #2
    (Throttle Ssr #2)
    Throttle sensor opener position No.2/
    Min.: 0 V, Max.: 4.9804 V
    2.2 to 2.6 V
    ETCS freeze data
    Throttle Sens Open #1(AD)
    (Thrtl Ssr #1 AD)
    Throttle sensor opener position No.1 (AD)/
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS freeze data
    Throttle Motor
    (Throttle Mot)
    Whether or not throttle motor control permitted/
    ON or OFF
    ON: Idling
    Read value with ignition switch to the ON position
    (Do not start engine)
    Throttle Motor Current
    (Throttle Mot)
    Throttle motor current/
    Min.: 0 A, Max.: 80 A
    0 to 3.0 A: Idling
    -
    Throttle Motor
    (Throttle Mot)
    Throttle motor/
    Min.: 0 %, Max.: 100 %
    0.5 to 40 %: Idling
    -
    Throttle Motor Current
    (Throttle Mot)
    Throttle motor current/
    Min.: 0 A, Max.: 19.92 A
    0 to 3.0 A: Idling
    -
    Throttle Motor Open Duty
    (Throtl Opn Duty)
    Throttle motor duty ratio (open)/
    Min.: 0 %, Max.: 100 %
    0 to 40 %: Idling
    When accelerator pedal depressed, duty ratio increased
    Throttle Motor Close Duty
    (Throtl Cls Duty)
    Throttle motor duty ratio (close)/
    Min.: 0 %, Max.: 100 %
    0 to 40 %: Idling
    When accelerator pedal released quickly, duty ratio increased
    Throttle Motor Duty (Open)
    (Thrtl Mot (Opn))
    Throttle motor duty ratio (open)/
    Min.: 0 %, Max.: 100 %
    -
    ETCS freeze data
    Throttle Motor Duty (Close)
    (Thrtl Mot (Cls))
    Throttle motor duty ratio (close)/
    Min.: 0 %, Max.: 100 %
    -
    ETCS freeze data
    O2S B1 S2*2
    Heated oxygen sensor output voltage for bank 1 sensor2/
    Min.: 0 V, Max.: 1.275 V
    0 to 0.9 V:
    Driving 70 km/h (44 mph)
    Performing Inj Vol or A/F Control function of ACTIVE TEST enables technician to check voltage output of sensor
    O2FT B1 S2*2
    Short-term fuel trim of associated with bank 1 sensor 2/
    Min.: -100 %, Max.: 99.2 %
    -20 to 20 %: Idling
    Same as Short FT #1
    Catalyst Temp (B1 S2)
    (Cat Temp B1S2)
    Catalyst temperature (Bank 1 sensor 2)/
    Min.: -40°C, Max.: 6,513.5°C
    -
    -
    Initial Engine Coolant Temp
    (Ini Cool Temp)
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    (Ini Intake Temp)
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    Close to ambient air temperature
    Service data
    Engine Coolant Temp (In)
    (Coolant Temp 2)
    Engine coolant (radiator) temperature/
    Min.: -40°C, Max.: 140°C
    80 to 100°C(176 to 212°F):
    After warming up
    If value -40°C, sensor circuit open
    If value 140°C, sensor circuit short
    Injection Volume (Cylinder1)
    (Inj Vol)
    Injection volume/
    Min.: 0 ml, Max.: 2.048 ml
    0 to 0.5 m
    Quantity of fuel injection volume for 10 times
    Starter Signal
    (Starter Sig)
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Power Steering Switch
    (PS SW)
    Power steering signal/
    ON or OFF
    ON: Power steering operation
    -
    Power Steering Signal
    (PS Signal)
    Power steering signal/
    ON or OFF
    ON: When steering wheel first turned after ignition switch turned to ON
    This signal status usually ON until ignition switch turned to OFF
    Closed Throttle Position SW
    (Ctp SW)
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    A/C Signal
    A/C signal/ ON or OFF
    ON: A/C ON
    -
    Electrical Load Signal
    (Elect Load Sig)
    Electrical load signal/
    ON or OFF
    ON: Headlights or defogger turned ON
    -
    Stop Light Switch
    (Stop Light SW)
    Stop light switch/
    ON or OFF
    ON: Brake pedal depressed
    -
    ETCS Actuator Power
    (+BM)
    Whether or not electronic throttle control system power input/
    ON or OFF
    ON: Idling
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 19.92 V
    10 to 15 V: Idling
    ETCS freeze data
    Battery Voltage
    (Batt)
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    9 to 14 V: Idling
    -
    Actuator Power Supply
    (Actuator Power)
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS freeze data
    Atmosphere Pressure
    (Atm Pressure)
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 150 kPa
    Equivalent to atmospheric pressure
    (absolute pressure)
    -
    EVAP Purge VSV *2
    (Evap(Purge)VSV)
    VSV status for EVAP control/
    ON or OFF
    -
    Active Test support data
    Fuel Pump/Speed Status
    (Fuel Pump / Spd)
    Fuel pump/speed status/
    ON or OFF
    -
    Active Test support data
    VVT Control Status (Bank1)
    (VVT Ctrl B1)
    VVT control status/ ON or OFF
    -
    Active Test support data
    Electric Fan Motor
    (Fan Motor)
    Electric fan motor status/
    ON or OFF
    -
    Active Test support data
    TC and TE1
    (TC/TE1)
    TC and TE terminals of DLC3/
    ON or OFF
    -
    -
    VVT Aim Angle (Bank1)
    (VVT Aim Angl#1)
    VVT aim angle (Bank 1)/
    Min.: 0 %, Max.: 100%
    0 %: Idling
    VVT duty signal value during intrusive operation
    VVT Change Angle (Bank1)
    (VVT Chng Angl#1)
    VVT change angle/ Min.: 0°FR, Max.: 60°FR
    0 to 5°FR: Idling
    Displacement angle during intrusive operation
    VVT OCV Duty (Bank1)
    (VVT Ocv Duty B1)
    VVT OCV operation duty/
    Min.: 0 %, Max.: 100%
    0 %: Idling
    Requested duty value for intrusive operation
    Idle Fuel Cut
    (FC Idl)
    Fuel cut idle/
    ON or OFF
    ON: Fuel cut operation
    FC Idl = "ON" when throttle valve fully closed and engine speed over 2,800 rpm
    FC TAU
    Fuel cut TAU (Fuel cut during very light load)/
    ON or OFF
    ON: Fuel cut operation
    Fuel cut initiated under very light load to prevent combustion
    # Codes
    # Codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    Check Mode
    Check mode/
    0: ON, 1: OFF
    Check mode ON
    Click here
    SPD Test
    Check mode result for vehicle speed sensor/
    0: COMPL, 1: INCOMPL
    -
    -
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    Engine Run Time
    (Eng Run Time)
    Engine run time/
    Min.: 0 second, Max.: 65,535 seconds
    Time after engine start
    Service data
    Time after DTC Cleared
    (Time DTC Clear)
    Time after DTC cleared/
    Min.: 0 minute, Max.: 65,535 minutes
    Equivalent to time after DTCs erased
    -
    Distance from DTC Cleared
    (Dist DTC Clear)
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65,535 km
    Equivalent to drive distance after DTCs erased
    -
    Warm-up Cycle Cleared DTC (Wu Cyc DTCclear)
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    Model Code
    Model code
    -
    Identifying model code:
    TRH2###
    Engine Type
    Engine type
    -
    Identifying engine type:
    2TR
    Cylinder Number
    (Cylinder)
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying cylinder number:
    4
    Transmission
    Transmission type
    -
    Identifying transmission type:
    MT, ECT
    Destination
    Destination
    -
    Identifying destination:
    W (Europe)
    Model Year
    Model year/
    Min.: 0, Max.: 255
    -
    Identifying model year:
    200#
    *: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.
    *2: Except leaded gasoline vehicle


ACTIVE TEST

HINT:
Performing an Active Test using the intelligent tester enables components including the relay, VSV, and actuator to be operated without removing any parts. Performing the Active Test as the first step of troubleshooting is one method of shortening diagnostic time.
Data List is displayed during an Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch to OFF.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn the intelligent tester ON.

  6. Select the following menu items: Powertrain / Engine and ECT / Active Test.

  7. Perform the Active Test by referring to the table below.

    Intelligent Tester
    (Abbreviation)
    Test details
    Control Ranges
    Diagnostic Note
    Control the Injection Volume
    (Inj Vol)
    Change injection volume
    Between -12 % and 25 %
    1. All injectors tested at the same time
    2. Perform test at less than 3,000 rpm
    3. Injection volume can be changed in 1 % graduations within control range
    Activate the VSV for Evap Control*1
    (Evap VSV (Alone))
    Activate EPAP VSV control
    ON/OFF
    -
    Control the Fuel Pump / Speed
    (Fuel Pump / Spd)
    Activate fuel pump
    ON/OFF
    -
    Activate the VVT System (Bank1)
    (VVT Ctrl B1)
    Turn ON and OFF OCV
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON
    2. Normal engine running or idling when OCV OFF
    Connect the TC and TE1
    (TC/TE1)
    Turn ON and OFF TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    (FC Idl Prohbt)
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the Electric Cooling Fan
    (Cooling Fan)
    Activate cooling fan
    ON/OFF
    -
    Control the ETCS Open/Close Slow Speed
    (ETCS Slow)
    Throttle actuator
    ON: throttle valve opens slowly
    1. Test possible when following conditions met:
      1. Ignition switch to the ON position
      2. Engine does not start
      3. Fully depressing accelerator pedal (APP: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed
    (ETCS Fast)
    Throttle actuator
    ON: throttle valve opens fast
    Same as above
    Control the Cylinder#4 Fuel Cut
    (Fuel Cut #4)
    Cylinder #1 injector fuel cut
    ON/OFF
    Test possible during vehicle stopping and engine idling
    Control the Cylinder#3 Fuel Cut
    (Fuel Cut #3)
    Cylinder #2 injector fuel cut
    ON/OFF
    Same as above
    Control the Cylinder#2 Fuel Cut
    (Fuel Cut #2)
    Cylinder #3 injector fuel cut
    ON/OFF
    Same as above
    Control the Cylinder#1 Fuel Cut
    (Fuel Cut #1)
    Cylinder #4 injector fuel cut
    ON/OFF
    Same as above
    Control the VVT Linear (Bank1)
    (VVT Linear B1)
    Activate OCV
    Min.: -127%, Max.: 127%
    Same as above
    *1: Except leaded gasoline vehicle