Home › ENGINE · 5L-E › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > Air Conditioning Signal Circuit

for Preparation Click here


DESCRIPTION

When the A/C compressor is on, the A/C amplifier sends the A/C signal to the ECM, then ECM increases the fuel injection volume to improve driveability during engine idling.

WIRING DIAGRAM


A110562E01


INSPECTION PROCEDURE


When using intelligent tester:

1.READ VALUE OF INTELLIGENT TESTER (AIR CONDITIONER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Air conditioning switch on.

  1. Select the item "Powertrain/Engine and ECT/Data List/A/C Signal" and read its value displayed on the intelligent tester.

    Result:

    A/C Compressor
    Display
    OFF
    A/C Signal OFF
    ON
    A/C Signal ON



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT ECM (CHECK VOLTAGE)


    A062416E16
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Connection
    Specified Condition
    AC1 (B8-2) - Body ground
    A/C compressor ON
    Below 1.5 V
    AC1 (B8-2) - Body ground
    A/C compressor OFF
    7.5 to 14 V



NG
Go to step 3
OK

REPLACE ECM 

3.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONER AMPLIFIER)


    A062418E02
  1. Disconnect the A/C amplifier H19 connector.

  1. Disconnect the ECM B8 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    AC1 (H19-8) (*1) - AC1 (B8-2)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    AC1 (B8-2) - Body ground
    10 kΩ or higher

    HINT:
    *1: Terminal arrangement (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONER AMPLIFIER 


When not using intelligent tester:

1.INSPECT ECM (CHECK VOLTAGE)


    A062416E16
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Connection
    Specified Condition
    AC1 (B8-2) - Body ground
    A/C compressor ON
    Below 1.5 V
    AC1 (B8-2) - Body ground
    A/C compressor OFF
    7.5 to 14 V



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.CHECK HARNESS AND CONNECTOR (ECM - AIR CONDITIONER AMPLIFIER)


    A062418E02
  1. Disconnect the A/C amplifier H19 connector.

  1. Disconnect the ECM B8 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    AC1 (H19-8) (*1) - AC1 (B8-2)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    AC1 (B8-2) - Body ground
    10 kΩ or higher

    HINT:
    *1: Terminal arrangement (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONER AMPLIFIER