Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB BOLT

FRONT AXLE HUB BOLT > REPLACEMENT

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE FRONT SPEED SENSOR (w/ ABS)


    C102281E01
  1. Remove the 2 bolts, and separate the speed sensor from the steering knuckle.

    NOTICE:
    1. Be careful not to damage the speed sensor.
    2. Prevent foreign matter from adhering to the speed sensor.



3. REMOVE FRONT DISC BRAKE CALIPER ASSEMBLY


    C102283E01
  1. Remove the 2 bolts, and disconnect the brake caliper assembly.

    NOTICE:
    Use a wire or an equivalent to keep the brake caliper from hanging down by the flexible hose.



4. REMOVE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and castle nut.



    C102285E01
  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09628-00011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Do not damage the brake dust cover.
    3. Make sure that the string of the SST is securely tied to the vehicle.



5. REMOVE FRONT AXLE ASSEMBLY


    C102287
  1. Remove the 4 bolts, 4 nuts and front axle assembly from the front suspension lower arm.

  1. Remove the cotter pin and castle nut.



    C102660E01
  1. Using SST, remove the front axle assembly from the front suspension upper arm.

    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.
    3. Make sure that the string of the SST is securely tied to the vehicle.



6. REMOVE FRONT LOWER BALL JOINT ASSEMBLY
  1. Fix the steering knuckle in the vise using aluminium plates.

    NOTICE:
    Do not damage the steering knuckle.

  1. Remove the cotter pin.

  1. Loosen the nut.



    C103882E01
  1. Use SST to separate the front lower ball joint assembly from the steering knuckle.

    SST
    09628-62011  

    NOTICE:
    1. Do not damage the ball joint dust boot.
    2. Apply grease to the threads and tip of the SST center bolt before use.

  1. Remove the nut and front lower ball joint assembly.



7. REMOVE STEERING KNUCKLE


    C103883E01
  1. Remove the 4 bolts.



    C103880E01
  1. Using SST, remove the steering knuckle, brake dust cover from the front axle hub sub-assembly.

    SST
    09950-40011   (09951-04020, 09953-04010, 09952-04010, 09955-04051)

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt (09953-04010) before use.



8. REMOVE FRONT DISC


    C102293E01
  1. Remove the 6 bolts.



    C113549E01
  1. Remove the front disc as shown in the illustration.



9. REMOVE FRONT AXLE HUB BOLT
  1. Hold the front axle hub sub-assembly in a vise between aluminium plates.

    NOTICE:
    Do not overtighten the vise.



    C102370E01
  1. Temporarily install the 2 nuts and 2 washers to the front axle hub bolts as shown in the illustration.

  1. Using SST and a screwdriver or an equivalent to hold the front axle hub sub-assembly, remove the front axle hub bolt.

    SST
    09650-17011  



10. INSTALL FRONT AXLE HUB BOLT
  1. Hold the front axle hub sub-assembly in a vise between aluminium plates.

    NOTICE:
    Do not overtighten the vise.



    C102371E01
  1. Install a washer and nut to a new front axle hub bolt as shown in the illustration.

  1. Using a screwdriver or an equivalent to hold the front axle hub sub-assembly, install a new front axle hub bolt by tightening the nut.



11. INSTALL FRONT DISC


    C113549E02
  1. Install the front disc as shown in the illustration.



    C102293E01
  1. Install the front disc with the 6 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



12. INSTALL FRONT LOWER BALL JOINT ASSEMBLY
  1. Fix the steering knuckle in the vise using aluminium plates.

    NOTICE:
    Do not damage the steering knuckle.

  1. Install the front lower ball joint assembly to the steering knuckle with the nut.

    Torque:
    170 N*m{ 1,730 kgf*cm , 125 ft.*lbf }

    NOTICE:
    1. Ensure that the thread and taper are free of oil etc.
    2. Do not damage the lower ball joint dust boot.

  1. Install a new cotter pin to the front lower ball joint assembly.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



13. INSTALL STEERING KNUCKLE


    C102290E01
  1. Install the steering knuckle and brake dust cover to the front axle hub sub-assembly with the 4 bolts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



14. INSTALL FRONT AXLE ASSEMBLY
  1. Temporarily install the front axle assembly to the front suspension upper arm and front suspension lower arm.



    C102287E02
  1. Fully tighten front suspension lower arm with the 4 bolts and 4 nuts.

    Torque:
    Nut (A):
    90 N*m{ 918 kgf*cm , 66 ft.*lbf }
    Nut (B):
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



    C102007E01
  1. Fully tighten the front suspension upper arm with the nut.

    Torque:
    113 N*m{ 1,147 kgf*cm , 83 ft.*lbf }

    NOTICE:
    Do not damage the lower ball joint dust boot.

  1. Install a new cotter pin to the front suspension upper arm.

    NOTICE:
    Further tighten the castle nut up to 60° if the holes for the cotter pin are not aligned.



15. INSTALL TIE ROD END SUB-ASSEMBLY
  1. Install the tie rod end sub-assembly to the steering knuckle with the castle nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

    NOTICE:
    Do not damage the lower ball joint dust boot.

  1. Install a new cotter pin to the tie rod end sub-assembly.

    NOTICE:
    Further tighten the castle nut up to 60° if the holes for the cotter pin are not aligned.



16. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


    C102283E01
  1. Install the brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    123 N*m{ 1,250 kgf*cm , 91 ft.*lbf }



17. INSTALL FRONT SPEED SENSOR (w/ ABS)


    C102281E01
  1. Install the speed sensor to the steering knuckle with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.



18. INSTALL FRONT WHEEL

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }



19. INSPECT WHEEL ALIGNMENT
(Click here)


20. CHECK ABS SPEED SENSOR SIGNAL (w/ ABS)
(Click here)