Home › ENGINE ยท 5L-E › FUEL › FUEL INJECTION PUMP

FUEL INJECTION PUMP > REMOVAL

for Preparation Click here



1. DRAIN ENGINE COOLANT
  1. Remove the radiator cap.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Check if there is any excessive deposits of rust or scale around the radiator cap and radiator filler hole. The coolant should be free from oil.

    HINT:
    If excessively dirty, clean the coolant passage and the coolant.

  1. Install the radiator cap.



2. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

HINT:
Use the same procedures described for the LH side. (Click here)



3. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

HINT:
Use the same procedures described for the LH side. (Click here)



4. REMOVE FRONT DOOR SCUFF PLATE RH


5. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Turn back the carpet, and remove the engine service hole cover sub-assembly.



6. REMOVE RADIATOR HOSE INLET


7. REMOVE VANE PUMP V BELT


    A071310E01
  1. Loosen the bolt A and nut B, and remove the V belt.



8. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1


    A074095E01
  1. Loosen the nut A and bolt B, and remove the V belt.



9. REMOVE FAN AND GENERATOR V BELT (w/o AIR CONDITIONING)


    A115631E01
  1. Loosen the bolts A and B, and remove the V belt.



10. REMOVE FAN AND GENERATOR V BELT (w/ AIR CONDITIONING)


    A115632E01
  1. Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.



11. REMOVE FAN PULLEY
  1. Remove the 4 nuts, fan spacer and fan pulley.



12. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (w/ AIR CONDITIONING)


    A115632E01
  1. Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.



13. REMOVE COMPRESSOR MOUNTING BRACKET (w/ AIR CONDITIONING)


    A112014
  1. Remove the 3 bolts and compressor mounting bracket.



    A112016
  1. Remove the bolt and spacer.



    A112015
  1. Remove the 4 bolts and compressor mounting bracket.



14. REMOVE VANE PUMP DRIVE PULLEY


    A112013
  1. w/o Air conditioning:

    1. Remove the 4 bolts, vane pump drive pulley and the vane pump drive pulley spacer.

  1. w/ Air conditioning:

    1. Remove the 4 bolts, 2 vane pump drive pulleys.



15. REMOVE CRANKSHAFT PULLEY


    A058720E01
  1. Using SST, remove the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A058719E01
  1. Using SST, remove the pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-60010   (09951-00490)
    09950-40011   (09957-04010)



16. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


    A112017
  1. Remove the 11 bolts, washers, timing belt cover and 2 gaskets.



17. REMOVE TIMING BELT GUIDE


18. SET NO.1 CYLINDER TO TDC/COMPRESSION


    A058728E01
  1. Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.



    A058729E01
  1. Check that the timing marks of the camshaft timing pulley and No.2 timing belt cover are aligned.
    If not, turn the crankshaft 1 revolution (360°).



19. REMOVE TIMING BELT


    A058721E01
  1. Remove the timing belt.

    HINT:
    If reusing the timing belt, draw a direction arrow on the timing belt (in the direction of engine revolution), and place matchmarks on the pulleys and timing belt.



    A058730E01
  1. Turn the crankshaft 90° counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing gear case.

    NOTICE:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley, causing damage. So always set the crankshaft pulley at the correct angle.



    A058731E01
  1. Loosen the timing belt idler No.1 bolt (A), and shift the idler to the left as far as possible.

  1. Temporarily tighten the pulley bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.



20. REMOVE AIR CLEANER HOSE NO.2
  1. Loosen the bolt, and disconnect the air cleaner hose No.2.



21. REMOVE INTAKE AIR CONNECTOR SUB-ASSEMBLY
  1. Disconnect the ventilation hose.

  1. Disconnect the turbo pressure sensor connector.



    A111051
  1. Remove the bolt, 3 nuts, intake air connector and gasket.



22. REMOVE VENTURI ASSEMBLY


    A111052E01
  1. Disconnect the throttle open switch connector.



    A111053E01
  1. Disconnect the throttle control motor connector.

  1. Remove the venturi and gasket.



23. REMOVE INJECTION PIPE SET
  1. Loosen the 8 union nuts of the 4 injection pipes.

  1. Remove the 2 nuts, 2 upper pipe clamps, and 4 injection pipes with lower pipe clamps.



24. REMOVE INJECTION PUMP DRIVE PULLEY


    A071313E01
  1. Using SST, remove the pulley nut.

    SST
    09213-14010   (91651-60865)
    09330-00021  



    A071314E01
  1. Using SST, remove the drive pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



25. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY
  1. Disconnect the engine speed sensor connector.

  1. Disconnect the spill control valve connector.

  1. Disconnect the correction unit connector.

  1. Disconnect the timer control valve connector.

  1. Disconnect the fuel temperature sensor connector.

  1. Disconnect the engine wire clamp.

  1. Disconnect the 3 fuel hoses.



    A071318
  1. Disconnect the 3 bolts and injection pump stay No.1.

  1. Remove the 2 nuts and injection or supply pump assembly.