Home › ENGINE ยท 5L-E › LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > REMOVAL

for Preparation Click here



1. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



  1. Loosen the radiator drain cock plug and engine drain plug, then drain the coolant.


    A114683E02

  1. Remove the radiator cap.



2. DRAIN ENGINE OIL


3. REMOVE FRONT SEAT ASSEMBLY RH


    B107528
  1. Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.



4. REMOVE FRONT DOOR SCUFF PLATE RH


5. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Turn back the carpet, and remove the engine service hole cover sub-assembly.



6. REMOVE INTAKE AIR CONNECTOR SUB-ASSEMBLY
  1. Disconnect the ventilation hose.

  1. Disconnect the turbo pressure sensor connector.



    A111051
  1. Remove the bolt, 3 nuts, intake air connector and gasket.



7. REMOVE INTAKE AIR CONNECTOR BRACKET


    A112061
  1. Remove the 2 bolts and intake air connector bracket.



8. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY


9. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the 2 bolts, oil level gage and oil level gage guide.



10. REMOVE VANE PUMP V BELT


    A071310E01
  1. Loosen the bolt A and nut B, and remove the V belt.



11. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (w/ Air Conditioning)


    A074095E01
  1. Loosen the nut A and bolt B, and remove the V belt.



12. REMOVE FAN AND GENERATOR V BELT (w/o Air Conditioning)


    A115631E01
  1. Loosen the bolts A and B, and remove the V belt.



13. REMOVE FAN AND GENERATOR V BELT (w/ Air Conditioning)


    A115632E01
  1. Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.



14. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning)



15. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning)


    A112014
  1. Remove the 3 bolts and compressor mounting bracket.



    A112016
  1. Remove the bolt and spacer.



    A112015
  1. Remove the 4 bolts and compressor mounting bracket.



16. REMOVE GENERATOR W/ VACUUM PUMP ASSEMBLY


    A112062
  1. Remove the bolt with the hose disconnected.

  1. Remove the clip with the hose disconnected.



    A113355
  1. Remove the bolt and generator w/ vacuum pump assembly.



17. REMOVE EXHAUST PIPE ASSEMBLY FRONT
(Click here)


18. REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO.1
  1. Remove the 3 bolts and exhaust manifold heat insulator No.1.



19. REMOVE EXHAUST MANIFOLD


    A113082
  1. Remove the 6 bolts, 2 nuts and exhaust manifold.

  1. Remove the exhaust manifold gasket from the cylinder head.



20. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Using SST, remove the oil filter.

    SST
    09228-44011  



21. REMOVE VACUUM PUMP OIL INLET HOSE


    A113492
  1. Remove the union bolt and 2 gaskets, and disconnect the vacuum pump oil inlet hose from the cylinder block.



22. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY


    A113493
  1. Remove the 10 bolts, 2 nuts, oil filter bracket, and gasket.



23. REMOVE OIL COOLER ASSEMBLY
  1. Remove the 4 nuts, oil cooler, and 2 gaskets.