DTC B1900/73 Short in Driver Side Front Pretensioner Squib Circuit |
DTC B1901/73 Open in Driver Side Front Pretensioner Squib Circuit |
DTC B1902/73 Short to GND in Driver Side Front Pretensioner Squib Circuit |
DTC B1903/73 Short to B+ in Driver Side Front Pretensioner Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1900/73 |
|
|
| B1901/73 |
|
|
| B1902/73 |
|
|
| B1903/73 |
|
|

| 1.CHECK FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SIDE FRONT PRETENSIONER SQUIB) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
LHD
Disconnect the connector from the front seat outer belt assembly LH.
RHD
Disconnect the connector from the front seat outer belt assembly RH.
Connect the white wire side of SST (resistance 2.1 Ω) to connector "C".
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector "C".
Check that the engine room main wire connector (on the front seat outer belt assembly side) is not damaged.
|
| ||||
| OK | |
| 3.CHECK ENGINE ROOM MAIN WIRE (DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT) |
![]() |
Disconnect the connectors from the center airbag sensor assembly.
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| B23-1 (L+) - Body ground (LHD) | Ignition switch ON | Below 1 V |
| B23-2 (L-) - Body ground (LHD) | Ignition switch ON | Below 1 V |
| B25-1 (R+) - Body ground (RHD) | Ignition switch ON | Below 1 V |
| B25-2 (R-) - Body ground (RHD) | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| B23-1 (L+) - B23-2 (L-) (LHD) | Always | Below 1 Ω |
| B25-1 (R+) - B25-2 (R-) (RHD) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| B23-1 (L+) - Body ground (LHD) | Always | 1 MΩ or higher |
| B23-2 (L-) - Body ground (LHD) | Always | 1 MΩ or higher |
| B25-1 (R+) - Body ground (RHD) | Always | 1 MΩ or higher |
| B25-2 (R-) - Body ground (RHD) | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector "B" (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| B23-1 (L+) - B23-2 (L-) (LHD) | Always | 1 MΩ or higher |
| B25-1 (R+) - B25-2 (R-) (RHD) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the front seat outer belt assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||