2014-2019 Hiace · Service Manual BRAKE

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built from Dec 2017

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the ABS warning light remains on:
  1. The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).
  2. There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.
  3. There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).
  4. The ABS control system is defective.

HINT:
In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C321579E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY
OK


3. INSPECT BATTERY


NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY
OK


4. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
  1. Turn the ignition switch off.

  1. C306843E08
    Disconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B92-12 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
C306843E03
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B92-25 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6. READ VALUE USING GTS (ABS WARNING LIGHT)
  1. Reconnect the B92 skid control ECU (brake actuator assembly) connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -

  1. Check the GTS display condition of the ABS warning light.

    Result:
    Result
    Proceed to
    Display of the Data List remains OFF
    A
    Display of the Data List remains ON
    B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT METER / GAUGE SYSTEM (Click here)


← ABS Warning Light Remains ON (Jan 2017 – Nov 2017)ABS Warning Light does not Come ON (Jan 2015 – Mar 2016) →