2014-2019 Hiace · Service Manual SUSPENSION & AXLE

C2177/77 Initialization not Completed

Diagnostic trouble codes · Vehicles built from Dec 2017

Versions by build date: Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

Initialization is necessary if one of the following occurs:
  1. The tire pressure warning ECU and receiver is replaced.
  2. A tire pressure warning valve and transmitter is replaced.
  3. Tires with a different tire standard pressure are installed.
  4. The tires are rotated.
  5. A new vehicle is delivered.
Tire pressure initialization is started by pressing and holding the tire pressure warning reset switch with the ignition switch to ON. The tire pressure warning ECU and receiver flashes the tire pressure warning light of the combination meter assembly 3 times and registers the tire pressure sent by the tire pressure warning valve and transmitter after receiving an initialization command signal.
DTC No.
DTC Detection Condition
Trouble Area
C2177/77
  1. All conditions below are met:
  1. During initialization
  2. Tire pressure warning valve and transmitter is not in stop mode.
  3. Signal is not received from tire pressure warning valve and transmitter for 20 minutes or more.
  4. Vehicle speed is more than 40 km/h (25 mph) for a total of 20 minutes.
  1. Tire pressure warning valve and transmitter
  2. Wire harness or connector
  3. Tire pressure warning ECU and receiver

WIRING DIAGRAM

C370426E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.


1. CHECK FREQUENCY RECEIVING CONDITION
  1. Check that the following conditions are not met:

    1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

      HINT:
      If the vehicle is located in an area such as the one described above, the tire pressure warning light may come on after blinking 1 minute only in a particular area due to interfering radio frequencies.

    2. Devices using similar radio frequencies are used in the vehicle.

      OK:
      Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

      HINT:
      Radio transmissions may be interrupted due to the surroundings or devices installed by the user.



NG
CHECK IF ANY DEVICE IS INSTALLED BY USER
OK


2. PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


3. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*
    ID 5 Tire Inflation Pressure
    ID5 tire inflation pressure/
    min.: Absolute pressure (abs)/ 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs)/ 900 kPa (9.2 kgf/cm2, 131 psi), Relative pressure (gauge)/ 800 kPa (8.2 kgf/cm2, 116 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*

    HINT:
    1. *: It may take a few minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.
    3. The wheel position cannot be determined from ID1 through ID5 on the Data List.


    Result:
    Result
    Proceed to
    All tire pressure readings are equal to specified values.
    A
    Tire pressure values are not displayed.
    B



B
GO TO DTC C2121/21 TO C2125/25 (Click here)
A

END


← C2177/77 Initialization not Completed (Jan 2017 – Nov 2017)C2198/98 Initialization Switch (for Test Mode DTC) (Jan 2017 – Nov 2017) →