2014-2019 Hiace · Service Manual ENGINE

B2271 Ignition Hold Monitor Malfunction

Diagnostic trouble codes · Vehicles built from Dec 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2271
When either of the following conditions is met (1-trip detection logic*):
  1. The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning.
  2. The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.
  1. AM2 fuse
  2. Certification ECU (smart key ECU assembly)
  3. Wire harness or connector
IG ON
  1. *: Only detected while a malfunction is present and the engine switch is on (IG)

HINT:
  1. The IG circuits activate the IG relays.
  2. After the IG circuits turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started).
The power source mode cannot be changed to on (IG).

WIRING DIAGRAM

C299863E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:
Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2271
Power Source Control
  1. IG Relay Monitor (Inside)
  2. Latch Circuit
Starting Control
  1. Ignition
-


1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.C299853E01

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B75-1 (+B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2. CHECK HARNESS AND CONNECTOR (GROUND)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.C299853E02

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-10 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.C299852E01

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B75-20 (IG1D) - Body ground
    Engine switch on (ACC) → Engine switch on (IG)
    1 V or less → 9 V or higher



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B2271 Ignition Hold Monitor Malfunction (Jan 2017 – Nov 2017)B2274 ACC Monitor Malfunction (Oct 2014 – Dec 2014) →