2014-2019 Hiace · Service Manual ENGINE

B2274 ACC Monitor Malfunction

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2274
Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).

HINT:
When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  1. AM2 fuse
  2. No. 2 Integration Relay (ACC relay)
  3. Certification ECU (smart key ECU assembly)
  4. Wire harness or connector
Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.
  1. *: Only detected while a malfunction is present.
Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
  1. If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.
  2. If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).

HINT:
The engine switch can be turned on (IG) and the engine can be started.

-
Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2274
Power Source Control
  1. ACC Relay Monitor
Starting Control
  1. Ignition
-

WIRING DIAGRAM

C300091E01

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.C299853E01

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B75-1 (+B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2. CHECK HARNESS AND CONNECTOR (GROUND)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.C299853E02

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-10 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the 12E No. 2 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-21 (ACCD) - 12E-8
    Always
    Below 1 Ω
    12E-4 - Body ground
    B75-21 (ACCD) or 12E-8 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK NO. 2 INTEGRATION RELAY (ACC RELAY)

  1. Remove the No. 2 integration relay.C302430E01

    Text in Illustration 
    *a
    Component without harness connected
    (No. 2 Integration Relay)
    -
    -

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12E-7 - 12E-9
    Battery voltage not applied to terminals 12E-8 and 12E-4
    10 kΩ or higher
    Battery voltage applied to terminals 12E-8 and 12E-4
    Below 1 Ω



NG
REPLACE NO. 2 INTEGRATION RELAY
OK


5. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Install the No. 2 integration relay.

  1. Measure the voltage according to the value(s) in the table below.C299852E02

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B75-21 (ACCD) - Body ground
    Engine switch off → Engine switch on (ACC)
    1 V or less → 8.5 V or higher



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B2271 Ignition Hold Monitor Malfunction (from Dec 2017)B2274 ACC Monitor Malfunction (Jan 2015 – Mar 2016) →