DATA LIST / ACTIVE TEST
System information · Vehicles built from Dec 2017
Versions by build date: Jan 2015 – Nov 2017 from Dec 2017
| DATA LIST |
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light / ON or OFF
ON: Warning light on
OFF: Warning light off
-
Brake Warning Light
Brake warning light / ON or OFF
ON: Warning light on
OFF: Warning light off
-
Stop Light SW
Stop light switch assembly / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch assembly / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Gear Position
Gear position information / Fail, 1st-7th, "P, N", 8-10th, R or Not R
Actual gear position
-
Shift Lever Position
Shift lever position information / Fail, 1st-5th, 6th/B, D/M, "P, N" or R
Actual shift lever position
-
Inspection Mode
Inspection mode / Other or Inspect
Inspect: Inspection mode
Other: Normal mode
-
Zero Point of M/C
Memorized zero value / Min.: -12.50 Mpa, Max.: 12.40 Mpa
-
After master cylinder pressure sensor zero point calibration: 2.44 to 2.46 MPa
Deceleration Sensor
Acceleration sensor / Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
During deceleration/acceleration: Changes continuously
Zero Point of Decele
Memorized zero value / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
-
-
Deceleration Sensor2
Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
During deceleration/acceleration: Changes continuously
Zero Point of Decele2
Memorized zero value / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
-
-
Yaw Rate Sensor
Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate
Memorized zero value / Min.: - 128°, Max.: 127°
-
After completing zero point calibration: 0°
Steering Angle Sensor
Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
Turning left: Increases
Turning right: Decreases
-
Zero Point of Steering Angle
Memorized zero value / Min.: -3276.8°, Max.: 3276.7°
-
After steering angle sensor zero point calibration: 0°
Lateral G
Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
During turning: Changes in proportion with acceleration
Forward and Rearward G
Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
During acceleration/deceleration: Changes in proportion with acceleration
Yaw Rate Value
Yaw rate value / Min.: -128°/s, Max.: 127°/s
-
During turning: Changes in proportion with yaw
Steering Angle Value
Steering angle value / Min.: -3276.8°, Max.: 3276.7°
-
During steering operation: Changes in proportion with steering wheel rotation
Stop Light Relay
Stop Light Relay status / ON or OFF
OFF: Always
-
Slip Indicator Light
Slip indicator light / ON or OFF
ON: Indicator light on
OFF: Indicator light off
-
FR Wheel Speed
Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
FL Wheel Speed
Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RR Wheel Speed
Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
RL Wheel Speed
Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
Vehicle Speed
Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph)
When driving at constant speed: No large fluctuations
FR Wheel Acceleration
Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
During deceleration/acceleration: Changes continuously
FL Wheel Acceleration
Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
During deceleration/acceleration: Changes continuously
RR Wheel Acceleration
Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
During deceleration/acceleration: Changes continuously
RL Wheel Acceleration
Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
During deceleration/acceleration: Changes continuously
Stop Light Relay Output
Stop Light Relay status / ON or OFF
OFF: Always
-
FR Wheel ABS Ctrl Status
Front wheel RH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel ABS Ctrl Status
Front wheel LH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel ABS Ctrl Status
Rear wheel RH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel ABS Ctrl Status
Rear wheel LH ABS control status / ON or OFF
ON: During control
OFF: Not during control
-
BA Ctrl Status
BA control status / ON or OFF
ON: During control
OFF: Not during control
-
PBA Ctrl Status
PBA control status / ON or OFF
OFF: Always
-
TRC(TRAC) Ctrl Status
TRC control status / ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Engine Ctrl Status
TRC engine control status / ON or OFF
ON: During control
OFF: Not during control
-
TRC(TRAC) Brake Ctrl Status
TRC brake control status / ON or OFF
ON: During control
OFF: Not during control
-
FR Wheel VSC Ctrl Status
Front wheel RH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel VSC Ctrl Status
Front wheel LH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel VSC Ctrl Status
Rear wheel RH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel VSC Ctrl Status
Rear wheel LH VSC control status / ON or OFF
ON: During control
OFF: Not during control
-
Engine Revolutions
Engine speed / Min.: 0 rpm, Max.: 65535 rpm
Engine stopped: 0 rpm
When engine speed is constant: No large fluctuations
Real Engine Torque
Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
-
-
Accelerator Opening Angle %
Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0%
Accelerator pedal released: 0%
During accelerator pedal operation: Changes in proportion with the pedal movement
Solenoid Relay
Solenoid relay / ON or OFF
ON: Solenoid relay on
OFF: Solenoid relay off
-
ECB Motor Relay
Motor relay / ON or OFF
ON: Motor relay on
OFF: Motor relay off
ECB: Electronically Controlled Brake
TR(A)C/VSC Solenoid (SM2)
Master cut solenoid (SM2) / ON or OFF
ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SM1)
Master cut solenoid (SM1) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRH)
ABS solenoid (SFRH) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR)
ABS solenoid (SFRR) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH)
ABS solenoid (SFLH) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR)
ABS solenoid (SFLR) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH)
ABS solenoid (SRRH) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR)
ABS solenoid (SRRR) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH)
ABS solenoid (SRLH) / ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR)
ABS solenoid (SRLR) / ON or OFF
ON: Operating
OFF: Not operating
-
FR Speed Open
Front speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Open
Front speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
RR Speed Open
Rear speed sensor RH open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Open
Rear speed sensor LH open detection / Error or Normal
Normal
Error: Momentary interruption
EFI Communication Open
ECM communication open detection / Error or Normal
Normal
Error: Momentary interruption
Yaw Rate Open
Yaw rate sensor open detection / Error or Normal
Normal
Error: Momentary interruption
Deceleration Open
Acceleration sensor open detection / Error or Normal
Normal
Error: Momentary interruption
Steering Open
Steering angle sensor open detection / Error or Normal
Normal
Error: Momentary interruption
Master Cylinder Open
Master cylinder pressure sensor open detection / Error or Normal
Normal
Error: Momentary interruption
IG1 Voltage Value
IG1 voltage value / Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
Changes in proportion to battery voltage
BS1 Voltage Value
+BS voltage value / Min.: 0.00 V, Max.: 20.00 V
-
Changes in proportion to battery voltage
MT Voltage Value
Motor voltage value / Min.: 0.00 V, Max.: 20.00 V
-
Changes in proportion to battery voltage
TRC/VSC Off Mode
TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF
Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
Unknown: Unspecified
Number of DTC
Number of DTCs recorded / Min.: 0, Max.: 255
0
-
FR Speed Sensor Voltage Open
Front speed sensor RH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
FL Speed Sensor Voltage Open
Front speed sensor LH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
RR Speed Sensor Voltage Open
Rear speed sensor RH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
RL Speed Sensor Voltage Open
Rear speed sensor LH voltage open detection / Error or Normal
Normal
Error: Momentary interruption
M/C Pressure Sensor Noise
Master cylinder pressure sensor noise detection / Error or Normal
Normal
Error: Momentary interruption
Yaw Rate Sensor Voltage Open
Yaw rate sensor voltage open detection / Error or Normal
Normal
Error: Momentary interruption
EFI Communication Invalid
ECM communication invalid detection / Error or Normal
Normal
Error: Invalid
Reverse Position Switch
Shift lever R position status / ON or OFF
ON: Shift lever is in R
OFF: Shift lever is not in R
-
Master Cylinder Pressure
Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 23.28 MPa
Brake pedal operated: Proportional to pedal force
Brake pedal released: 0.00 to 1.76 MPa
-
Master Cylinder Sensor Temperature
Master cylinder pressure sensor temperature / Min.: -80°C (-112°F), Max.: 175°C (347°F)
Displays current master cylinder temperature
-
Motor Power Supply Voltage
Motor power source voltage / Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
Changes in proportion to battery voltage
Solenoid Power Supply Voltage
Solenoid power supply voltage / Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
Changes in proportion to battery voltage
Stop Light Relay State for ECU Control
Stop Light Relay status / ON or OFF
OFF: Always
-
Solenoid State for ECU Control
Solenoid (for ECU control) / ON or OFF
ON: Solenoid relay operating
OFF: Solenoid relay not operating
-
Motor State for ECU Control
Motor (for ECU control) / ON or OFF
ON: Motor relay operating
OFF: Motor relay not operating
-
Operation History of IG OFF while Vehicle is moving
History of ignition switch turned off when vehicle is in motion / ON or OFF
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
OFF: No history
-
Master Cylinder Pressure Sensor Power Supply Open
Master cylinder pressure sensor power supply voltage status / Error or Normal
Normal
Error: Momentary interruption
Solenoid Power Supply Open
Solenoid power supply voltage status / Error or Normal
Normal
Error: Momentary interruption
Motor Power Supply Open
Motor power supply voltage status / Error or Normal
Normal
Error: Momentary interruption
Stop Switch Open
Momentary interruption (open circuit) in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status / Error or Normal
Normal
Error: Momentary interruption
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON/OFF
Observe combination meter assembly
Vehicle condition: Vehicle stopped
Brake Warning Light
Brake warning light
Warning light ON/OFF
Observe combination meter assembly
Vehicle condition: Vehicle stopped
Solenoid Relay
Solenoid relay
Relay ON/OFF
Vehicle condition: Vehicle stopped
Motor Relay
Motor relay
Relay ON/OFF
Operating sound of motor can be heard.
Vehicle condition: Vehicle stopped
Stop Light Relay
Stop Light Relay
Relay ON/OFF
This item is displayed on GTS but is not used
ABS Solenoid (SRLR)
ABS solenoid (SRLR)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRLH)
ABS solenoid (SRLH)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRRR)
ABS solenoid (SRRR)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SRRH)
ABS solenoid (SRRH)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFLR)
ABS solenoid (SFLR)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFLH)
ABS solenoid (SFLH)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFRR)
ABS solenoid (SFRR)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
ABS Solenoid (SFRH)
ABS solenoid (SFRH)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
VSC/TRC Solenoid (SMR)
Master cut solenoid (SM2)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
VSC/TRC Solenoid (SMF)
Master cut solenoid (SM1)
Solenoid ON/OFF
Operating sound of solenoid (clicking sound) can be heard.
Vehicle condition: Vehicle stopped
TRC(TRAC) OFF Indicator Light
TRC OFF indicator light
Indicator light ON/OFF
Observe combination meter assembly
Vehicle condition: Vehicle stopped
VSC OFF Indicator Light
VSC OFF indicator light
Indicator light ON/OFF
Observe combination meter assembly
Vehicle condition: Vehicle stopped
Slip Indicator Light
Slip indicator light
Indicator light ON/OFF
Observe combination meter assembly
Vehicle condition: Vehicle stopped
EBS Relay
Emergency brake signal operation
Operation ON/OFF
Vehicle condition: Vehicle stopped
ABS Solenoid
Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible
Start/Stop
Vehicle condition: Vehicle stopped
VSC/TRC(TRAC) Solenoid
Selection of multiple VSC/TRC solenoids (SMR (SM2) and SMF (SM1)) possible
Start/Stop
Vehicle condition: Vehicle stopped