2014-2019 Hiace · Service Manual BRAKE

DATA LIST / ACTIVE TEST

System information · Vehicles built Jan 2015 – Nov 2017

Versions by build date: Jan 2015 – Nov 2017 from Dec 2017


DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  7. According to the display on the GTS, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Brake Warning Light
    Brake warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch assembly / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Gear Position
    Gear position information / Fail, 1st-7th, "P, N", 8th, R or Not R
    Actual gear position
    -
    Shift Lever Position
    Shift lever position information / Fail, 1st-5th, 6th/B, D/M, "P, N" or R
    Actual shift lever position
    -
    Inspection Mode
    Inspection mode / Other or Inspect
    Inspect: Inspection mode
    Other: Normal mode
    -
    Zero Point of M/C
    Memorized zero value / Min.: -12.50 Mpa, Max.: 12.40 Mpa
    -
    After master cylinder pressure sensor zero point calibration: 2.44 to 2.46 MPa
    Deceleration Sensor
    Acceleration sensor / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Zero Point of Decele
    Memorized zero value / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
    -
    -
    Deceleration Sensor2
    Acceleration sensor 2 / Min.: -18.525 m/s2, Max.: 18.387 m/s2
    -
    During deceleration/acceleration: Changes continuously
    Zero Point of Decele2
    Memorized zero value / Min.: - 25.10 m/s2, Max.: 24.90 m/s2
    -
    -
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128°/s, Max.: 127°/s
    Vehicle stopped: 0°/s
    Turning right: -128 to 0°/s
    Turning left: 0 to 127°/s
    -
    Zero Point of Yaw Rate
    Memorized zero value / Min.: - 128°, Max.: 127°
    -
    After completing zero point calibration: 0°
    Steering Angle Sensor
    Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
    Turning left: Increases
    Turning right: Decreases
    -
    Zero Point of Steering Angle
    Memorized zero value / Min.: -3276.8°, Max.: 3276.7°
    -
    After steering angle sensor zero point calibration: 0°
    Lateral G
    Lateral G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During turning: Changes in proportion with acceleration
    Forward and Rearward G
    Forward and backward G / Min.: -25.10 m/s2, Max.: 24.90 m/s2
    -
    During acceleration/deceleration: Changes in proportion with acceleration
    Yaw Rate Value
    Yaw rate value / Min.: -128°/s, Max.: 127°/s
    -
    During turning: Changes in proportion with yaw
    Steering Angle Value
    Steering angle value / Min.: -3276.8°, Max.: 3276.7°
    -
    During steering operation: Changes in proportion with steering wheel rotation
    Slip Indicator Light
    Slip indicator light / ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    Vehicle Speed
    Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FR Wheel Acceleration
    Front wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    FL Wheel Acceleration
    Front wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    RR Wheel Acceleration
    Rear wheel RH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    RL Wheel Acceleration
    Rear wheel LH acceleration / Min.: -200.84 m/s2, Max.: 199.27 m/s2
    -
    During deceleration/acceleration: Changes continuously
    FR Wheel ABS Ctrl Status
    Front wheel RH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    FL Wheel ABS Ctrl Status
    Front wheel LH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RR Wheel ABS Ctrl Status
    Rear wheel RH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RL Wheel ABS Ctrl Status
    Rear wheel LH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    BA Ctrl Status
    BA control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    TRC(TRAC) Ctrl Status
    TRC control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    TRC(TRAC) Engine Ctrl Status
    TRC engine control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    TRC(TRAC) Brake Ctrl Status
    TRC brake control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    FR Wheel VSC Ctrl Status
    Front wheel RH VSC control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    FL Wheel VSC Ctrl Status
    Front wheel LH VSC control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RR Wheel VSC Ctrl Status
    Rear wheel RH VSC control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RL Wheel VSC Ctrl Status
    Rear wheel LH VSC control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    Engine Revolutions
    Engine speed / Min.: 0 rpm, Max.: 65535 rpm
    Engine stopped: 0 rpm
    When engine speed is constant: No large fluctuations
    Real Engine Torque
    Real engine torque / Min.: -1024.0 Nm, Max.: 1023.0 Nm
    -
    -
    Accelerator Opening Angle %
    Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0%
    Accelerator pedal released: 0%
    During accelerator pedal operation: Changes in proportion with the pedal movement
    Solenoid Relay
    Solenoid relay / ON or OFF
    ON: Solenoid relay on
    OFF: Solenoid relay off
    -
    ECB Motor Relay
    Motor relay / ON or OFF
    ON: Motor relay on
    OFF: Motor relay off
    ECB: Electronically Controlled Brake
    TR(A)C/VSC Solenoid (SM2)
    Master cut solenoid (SM2) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    TR(A)C/VSC Solenoid (SM1)
    Master cut solenoid (SM1) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR) / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RR Speed Open
    Rear speed sensor RH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Open
    Rear speed sensor LH open detection / Error or Normal
    Normal
    Error: Momentary interruption
    EFI Communication Open
    ECM communication open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Yaw Rate Open
    Yaw rate sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Deceleration Open
    Acceleration sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Steering Open
    Steering angle sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    Master Cylinder Open
    Master cylinder pressure sensor open detection / Error or Normal
    Normal
    Error: Momentary interruption
    BS1 Voltage Value
    +BS voltage value / Min.: 0.00 V, Max.: 20.00 V
    -
    Changes in proportion to battery voltage
    MT Voltage Value
    Motor voltage value / Min.: 0.00 V, Max.: 20.00 V
    -
    Changes in proportion to battery voltage
    TRC/VSC Off Mode
    TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    VSC OFF: VSC off mode
    Unknown: Unspecified
    Number of DTC
    Number of DTCs recorded / Min.: 0, Max.: 255
    0
    -
    FR Speed Sensor Voltage Open
    Front speed sensor RH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    FL Speed Sensor Voltage Open
    Front speed sensor LH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RR Speed Sensor Voltage Open
    Rear speed sensor RH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    RL Speed Sensor Voltage Open
    Rear speed sensor LH voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    M/C Pressure Sensor Noise
    Master cylinder pressure sensor noise detection / Error or Normal
    Normal
    Error: Momentary interruption
    Yaw Rate Sensor Voltage Open
    Yaw rate sensor voltage open detection / Error or Normal
    Normal
    Error: Momentary interruption
    EFI Communication Invalid
    ECM communication invalid detection / Error or Normal
    Normal
    Error: Invalid
    Reverse Position Switch
    Shift lever R position status / ON or OFF
    ON: Shift lever is in R
    OFF: Shift lever is not in R
    -
    Master Cylinder Pressure
    Master cylinder pressure sensor pressure / Min.: 0.00 MPa, Max.: 23.28 MPa
    Brake pedal operated: Proportional to pedal force
    Brake pedal released: 0.00 to 1.76 MPa
    -
    Master Cylinder Sensor Temperature
    Master cylinder pressure sensor temperature / Min.: -80°C (-112°F), Max.: 175°C (347°F)
    Displays current master cylinder temperature
    -
    Motor Power Supply Voltage
    Motor power source voltage / Min.: 0.00 V, Max.: 20.00 V
    Ignition switch ON: 11 to 14 V
    Changes in proportion to battery voltage
    Solenoid Power Supply Voltage
    Solenoid power supply voltage / Min.: 0.00 V, Max.: 20.00 V
    Ignition switch ON: 11 to 14 V
    Changes in proportion to battery voltage
    Solenoid State for ECU Control
    Solenoid (for ECU control) / ON or OFF
    ON: Solenoid relay operating
    OFF: Solenoid relay not operating
    -
    Motor State for ECU Control
    Motor (for ECU control) / ON or OFF
    ON: Motor relay operating
    OFF: Motor relay not operating
    -
    Operation History of IG OFF while Vehicle is moving
    History of ignition switch turned off when vehicle is in motion / ON or OFF
    ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
    OFF: No history
    -
    Master Cylinder Pressure Sensor Power Supply Open
    Master cylinder pressure sensor power supply voltage status / Error or Normal
    Normal
    Error: Momentary interruption
    Solenoid Power Supply Open
    Solenoid power supply voltage status / Error or Normal
    Normal
    Error: Momentary interruption
    Motor Power Supply Open
    Motor power supply voltage status / Error or Normal
    Normal
    Error: Momentary interruption
    Stop Switch Open
    Momentary interruption (open circuit) in wire harness between skid control ECU (brake actuator assembly) and stop light switch assembly status / Error or Normal
    Normal
    Error: Momentary interruption


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  7. According to the display on the GTS, perform the Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    ABS Warning Light
    ABS warning light
    Warning light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped
    Solenoid Relay
    Solenoid relay
    Relay ON/OFF
    Vehicle condition: Vehicle stopped
    Motor Relay
    Motor relay
    Relay ON/OFF
    Operating sound of motor can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    VSC/TRC Solenoid (SMR)
    Master cut solenoid (SM2)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    VSC/TRC Solenoid (SMF)
    Master cut solenoid (SM1)
    Solenoid ON/OFF
    Operating sound of solenoid (clicking sound) can be heard.
    Vehicle condition: Vehicle stopped
    TRC(TRAC) OFF Indicator Light
    TRC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped
    VSC OFF Indicator Light
    VSC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped
    Slip Indicator Light
    Slip indicator light
    Indicator light ON/OFF
    Observe combination meter assembly
    Vehicle condition: Vehicle stopped
    ABS Solenoid
    Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible
    Start/Stop
    Vehicle condition: Vehicle stopped
    VSC/TRC(TRAC) Solenoid
    Selection of multiple VSC/TRC solenoids (SMR (SM2) and SMF (SM1)) possible
    Start/Stop
    Vehicle condition: Vehicle stopped

← FAIL-SAFE CHART (from Dec 2017)DATA LIST / ACTIVE TEST (from Dec 2017) →