2014-2019 Hiace · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 from Apr 2016


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A339229E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A339230E01
    Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.
    Text in Illustration 
    *a
    Tab
    *b
    Cutout

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Place the generator drive end frame on the generator pulley with clutch.

  1. Install the generator rotor assembly to the generator drive end frame.


3. INSTALL GENERATOR BEARING COVER PACKING

NOTICE:
A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.

  1. A314531E01
    Install a new generator bearing cover packing to the generator coil assembly.
    Text in Illustration 
    *a
    Protrusion
    *b
    Groove

    NOTICE:
    Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.


4. INSTALL GENERATOR COIL ASSEMBLY

  1. A339231E01
    Using a 21 mm deep socket wrench and press, slowly press on the generator coil assembly.

  1. Install the generator coil assembly with the 4 bolts.

    Torque:
    5.6 N*m{ 59 kgf*cm , 52 in.*lbf }


5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A153827E01
    While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the generator brush holder hole.
    Text in Illustration 
    *a
    Pin

  1. A284142E01
    Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

    Text in Illustration 
    *a
    Pin

  1. Pull out the pin from the generator brush holder assembly.


6. INSTALL GENERATOR TERMINAL INSULATOR
  1. Install the generator terminal insulator to the generator coil assembly.

    NOTICE:
    Make sure that the generator terminal insulator is installed with the correct orientation.


7. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover to the generator coil assembly with the 3 bolts.

    Torque:
    4.6 N*m{ 47 kgf*cm , 41 in.*lbf }


8. INSTALL GENERATOR PULLEY WITH CLUTCH
  1. Mount the generator assembly in a vise between aluminum plates.

  1. Temporarily install the generator pulley with clutch by hand.

  1. A339232E01
    Install SST A and SST B to the generator pulley with clutch as shown in the illustration.
    SST
    09820-63021  
    Text in Illustration 
    *a
    Generator Rotor Shaft

    NOTICE:
    Securely attach SST to the generator pulley with clutch and generator rotor shaft.

  1. A339234E01
    Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

    Torque:
    Specified tightening torque:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Torque Wrench Fulcrum Length
    *c
    SST Fulcrum Length
    V100135
    Turn

    NOTICE:
    Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

    HINT:
    1. Calculate the torque wrench reading when charging the fulcrum length of the torque wrench. (See page (Click here).)
    2. When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)): 64 N*m (653 kgf*cm, 47 ft.*lbf)

  1. Remove SST from the generator assembly.

  1. Check that the generator pulley with clutch rotates smoothly.

  1. Remove the generator assembly from the vise.


9. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator pulley with clutch.

← REASSEMBLY (Oct 2014 – Dec 2014)REASSEMBLY (from Apr 2016) →