2014-2019 Hiace · Service Manual SUSPENSION & AXLE

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. REMOVE REAR SKID CONTROL ROTOR (w/ ABS)

  1. C102233E01
    Temporarily install the nut to the rear brake backing plate No.1 bolt as shown in the illustration.

  1. Using a hammer, remove the 4 bolts from the rear axle shaft bearing case.

    NOTICE:
    Do not reuse the nuts previously removed from the vehicle.

  1. C102234
    Grind the bearing retainer inner and skid control rotor rear surfaces using a grinder, then chisel them out with a chisel.

    NOTICE:
    Be careful not to damage the rear axle shaft and backing plate.


2. REMOVE REAR AXLE SHAFT SNAP RING

  1. C102235
    Using a snap ring expander, remove the rear axle shaft snap ring.


3. REMOVE REAR AXLE SHAFT

  1. C102236E01
    Install a washer and nut to the rear brake backing plate No.1 bolt as shown in the illustration.

  1. Install the rear brake backing plate No.1 bolt by tightening the nut.

  1. C320854E01
    Install the rear axle shaft puller and rear axle shaft puller attachment with the 4 bolts.
    SST
    09521-25012  
    09521-25024  

    HINT:
    1. Uniformly tighten the 4 SST bolts.
    2. Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf).

  1. Secure SST to the rear axle bearing case with the 4 nuts.

    SST
    09521-25012  
    09521-25024  

  1. Using SST and a press, remove the rear axle shaft from the rear axle bearing case.

    SST
    09521-25012  
    09521-25024  

    NOTICE:
    Be careful not to drop the rear axle shaft.


4. REMOVE REAR AXLE BEARING RETAINER INNER
  1. Remove the rear axle bearing retainer inner.


5. REMOVE BRAKE DRUM OIL DEFLECTOR

  1. C102238E01
    Using SST, remove the rear axle hub bolts.
    SST
    09650-17011  

  1. Remove the brake drum oil deflector and brake drum oil deflector gasket.


6. REMOVE REAR AXLE SHAFT OUTER OIL SEAL

  1. C102239E01
    Using SST, remove the rear axle shaft outer oil seal.
    SST
    09308-00010  


7. REMOVE REAR AXLE SHAFT BEARING

  1. C102240E01
    Using SST and a press, remove the rear axle shaft bearing from the rear axle shaft bearing case.
    SST
    09223-56010  
    09950-60010   (09951-00600)


8. REMOVE REAR AXLE BEARING CASE

  1. C102241
    Temporarily install the nut to the rear brake backing plate No.1 bolt as shown in the illustration.

  1. Using a hammer, remove the 4 bolts from the rear axle shaft bearing case.

    NOTICE:
    Do not reuse the nuts previously removed from the vehicle.


9. INSPECT REAR AXLE SHAFT

  1. C179625
    Using a dial indicator, inspect the rear axle shaft runout and flange runout.

    Maximum:
    Shaft runout:
    1.5 mm (0.0591 in.)
    Flange runout:
    0.1 mm (0.00393 in.)

    NOTICE:
    Ensure that the dial indicator is set at right angles to the measurement surface.

    If runout exceeds the maximum, replace the rear axle shaft.

  1. Check the rear axle shaft for damage.

← REMOVAL (from Oct 2014)REASSEMBLY (from Oct 2014) →