2014-2019 Hiace · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. REMOVE REAR WHEEL

2. DRAIN BRAKE FLUID

3. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

  1. Release the parking brake lever, and remove the brake drum.

    C263541E01

    Text in Illustration 
    *A
    for 295 mm Drum
    *B
    for 254 mm Drum

    HINT:
    If the brake drum cannot be removed easily, perform the following steps.

  1. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.


4. REMOVE REAR AXLE BRAKE DRUM GASKET

5. REMOVE AUTOMATIC ADJUST LEVER

  1. for 254 mm drum:

    1. C102605
      Remove the automatic adjust lever and the tension spring.


6. SEPARATE PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C231698E01
      Using SST, remove the upper side tension spring from the brake shoe.
      SST
      09703-30011  

  1. for 295 mm drum:

    1. C263526E01
      Using SST, remove the upper side tension spring from the brake shoe.
      SST
      09703-30011  


7. REMOVE FRONT BRAKE SHOE

  1. for 254 mm drum:

    1. C102600
      Using a needle-nose pliers, remove the anchor side tension spring.

    2. C102601E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    3. C264220E02
      Remove the parking brake shoe lower strut.
      Text in Illustration 
      *A
      LH Side
      *B
      RH Side

    4. Separate the brake shoe return spring, and remove the front brake shoe.

  1. for 295 mm drum:

    1. C263527E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    2. Separate the brake shoe return spring, and remove the front brake shoe.


8. REMOVE REAR BRAKE SHOE

  1. for 254 mm drum:

    1. C102603E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    2. C102606
      Disconnect the parking brake cable No. 3 and remove the rear brake shoe.

  1. for 295 mm drum:

    1. C263528E01
      Using SST, remove the cup, shoe hold-down sprig and pin.
      SST
      09718-00011  

    2. Remove the tension spring.

    3. C263529
      Disconnect the parking brake cable No. 3 and remove the rear brake shoe.


9. REMOVE PARKING BRAKE SHOE STRUT SET

  1. for 254 mm drum:

    1. C102607E02
      Using a screwdriver, remove the C-washer, brake shoe lever, rear cushion lever and brake shoe strut set from the brake shoe.
      Text in Illustration 
      *1
      Brake Shoe Lever
      *2
      Brake Shoe Strut Set
      *3
      Rear Brake Shoe
      *4
      Rear Cushion Lever
      *5
      C-washer

    2. Remove the adjusting bolt and tension spring from the brake shoe strut set.

  1. for 295 mm drum:

    1. C263530E01
      Remove the brake shoe strut set.
      Text in Illustration 
      *1
      Rear Brake Shoe
      *2
      Brake Shoe Strut Set
      *3
      Brake Shoe Lever
      *4
      Automatic Adjust Lever
      *5
      C-washer
      *6
      E-ring

    2. Using a screwdriver, remove the E-ring and automatic adjust lever.

    3. Using a screwdriver, remove the C-washer and brake shoe lever from the brake shoe.


10. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.3

  1. C102159
    Remove the 2 bolts and separate the parking brake cable assembly No.3 from the rear brake backing plate.


11. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY

  1. C102608
    Using a union nut wrench, disconnect the brake tube, use a container to catch brake fluid.

  1. Remove the 2 bolts and wheel cylinder.


12. SEPARATE REAR SPEED SENSOR (w/ ABS)

  1. Disconnect the sensor connector.

    C281302

  1. Detach the 4 clamps.

  1. Remove the bolt and rear speed sensor LH.

    NOTICE:
    Prevent foreign matter from attaching to the sensor tip.

  1. Remove the O-ring from the rear speed sensor.


13. REMOVE REAR AXLE SHAFT WITH BACKING PLATE

  1. C102664J01
    Remove the 4 nuts and rear axle shaft with backing plate.

    NOTICE:
    1. Be careful not to damage the rear axle shaft oil seal.
    2. Be careful not to damage the skid control rotor rear.


14. REMOVE BEARING RETAINER O-RING
  1. Remove the bearing retainer O-ring from the rear axle housing assembly.


15. REMOVE REAR AXLE SHAFT OIL SEAL

  1. C102232E01
    Using SST, remove the rear axle shaft oil seal from the rear axle housing assembly.
    SST
    09308-00010  

← ON-VEHICLE INSPECTION (from Oct 2014)DISASSEMBLY (from Oct 2014) →