REMOVAL
Removal / installation · Vehicles built Oct 2014 – Nov 2015
Versions by build date: Oct 2014 – Nov 2015 from Dec 2015
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN MANUAL TRANSMISSION OIL |
Remove the filler plug and gasket.
Remove the drain plug and gasket, and drain the oil.
Install the drain plug with a new gasket.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 3. REMOVE EXHAUST PIPE ASSEMBLY FRONT NO.2 (for Long Wheelbase) |
Remove the 4 bolts, 2 compression springs.
Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front No.2 and 2 gaskets.
| 4. REMOVE EXHAUST PIPE ASSEMBLY FRONT NO.2 (for Super Long Wheelbase) |
Remove the 4 bolts, 2 nuts, 2 compression springs.
Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front No.2 and 2 gaskets.
| 5. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase) |
Put matchmarks on both flanges.

Remove the 4 nuts, bolts and washers.
- HINT:
- If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.
Remove the propeller shaft assembly.
Insert SST in the transmission to prevent oil leakage.

- NOTICE:
- Do not damage the oil seal.
Use the following SST for the automatic transmission
- SST
- 09325-40010
Use the following SST for the manual transmission
- SST
- 09325-20010
| 6. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase) |
Put matchmarks on both flanges.

Remove the 4 nuts, bolts and washers.
- HINT:
- If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.
Remove the 2 bolts and center support bearing assembly No.1.

Remove the propeller with center bearing shaft assembly.
Insert SST in the transmission to prevent oil leakage.

- NOTICE:
- Do not damage the oil seal.
Use the following SST for the automatic transmission.
- SST
- 09325-40010
Use the following SST for the manual transmission.
- SST
- 09325-20010
| 7. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY |
Put matchmarks on the control cable assembly and the outer lever.

Remove the 2 nuts and separate the transmission control cable from the outer lever.
Using a screwdriver, disengage the claws of the 2 clips.

Remove the transmission control cable and 2 clips from the transmission control cable bracket No.1.
| 8. DISCONNECT WIRE HARNESS |
Disconnect the 2 connectors and clamp.

| 9. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY |
Remove the 2 bolts and separate the clutch release cylinder.

| 10. REMOVE STARTER ASSEMBLY (for 2.2 kW Type) |
Disconnect the starter connector.
Remove the terminal cap.
Remove the nut, and disconnect the 30 terminal.
Remove the nut, 2 bolts, and stay.
Remove the nut 2 bolts, and starter assembly.
| 11. REMOVE STARTER ASSEMBLY (for 2.7 kW Type) |
Disconnect the starter connector.
Remove the terminal cap.
Remove the nut, and disconnect the 30 terminal.
Remove the nut and, 2 bolts, stay and starter assembly.
| 12. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY |
Support the manual transmission unit with a transmission jack.

Remove the bolt, nut, and 2 washers, and separate the transmission unit from the frame.
Remove the 8 bolts and manual transmission unit.

| 13. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY |
Remove the 4 bolts and rear engine mounting insulator assembly.

| 14. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 |
Remove the 2 bolts and transmission control cable bracket No.1.

