2014-2019 Hiace · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Dec 2015

Versions by build date: Oct 2014 – Nov 2015 from Dec 2015


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the filler plug and gasket.

  1. C350549E02
    Using a 10 mm hexagon socket wrench, remove the drain plug and gasket, and drain the oil.
    Text in Illustration 
    *1
    Gasket
    *2
    Drain Plug

  1. Using a 10 mm hexagon socket wrench, install the drain plug with a new gasket.

    Torque:
    44 N*m{ 450 kgf*cm , 33 ft.*lbf }


3. REMOVE EXHAUST PIPE ASSEMBLY FRONT NO.2 (for Long Wheelbase)
  1. Remove the 4 bolts, 2 compression springs.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front No.2 and 2 gaskets.


4. REMOVE EXHAUST PIPE ASSEMBLY FRONT NO.2 (for Super Long Wheelbase)
  1. Remove the 4 bolts, 2 nuts, 2 compression springs.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front No.2 and 2 gaskets.


5. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  


6. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.

  1. C107214
    Remove the 2 bolts and center support bearing assembly No.1.

  1. Remove the propeller with center bearing shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission.

      SST
      09325-40010  

    2. Use the following SST for the manual transmission.

      SST
      09325-20010  


7. SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C102206E01
    Put matchmarks on the control cable assembly and the outer lever.

  1. Remove the 2 nuts and separate the transmission control cable from the outer lever.

  1. C102207
    Using a screwdriver, disengage the claws of the 2 clips.

  1. Remove the transmission control cable and 2 clips from the transmission control cable bracket No.1.


8. DISCONNECT WIRE HARNESS

  1. C112944
    Disconnect the 2 connectors and clamp.


9. SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

  1. C102209
    Remove the 2 bolts and separate the clutch release cylinder.


10. REMOVE STARTER ASSEMBLY (for 2.2 kW Type)
  1. Disconnect the starter connector.

  1. Remove the terminal cap.

  1. Remove the nut, and disconnect the 30 terminal.

  1. Remove the nut, 2 bolts, and stay.

  1. Remove the nut 2 bolts, and starter assembly.


11. REMOVE STARTER ASSEMBLY (for 2.7 kW Type)
  1. Disconnect the starter connector.

  1. Remove the terminal cap.

  1. Remove the nut, and disconnect the 30 terminal.

  1. Remove the nut and, 2 bolts, stay and starter assembly.


12. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

  1. C102212
    Support the manual transmission unit with a transmission jack.

  1. Remove the bolt, nut, and 2 washers, and separate the transmission unit from the frame.

  1. C112945
    Remove the 8 bolts and manual transmission unit.


13. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY

  1. C102216
    Remove the 4 bolts and rear engine mounting insulator assembly.


14. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1

  1. C112943
    Remove the 2 bolts and transmission control cable bracket No.1.

← REMOVAL (Oct 2014 – Nov 2015)INSTALLATION (Oct 2014 – Dec 2014) →