INSTALLATION
Removal / installation · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
| 1. INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY |
Install the rear engine mounting insulator assembly with the 4 bolts.

- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
| 2. INSTALL EXTENSION HOUSING DYNAMIC DAMPER (WITH DYNAMIC DAMPER) |
![]() ![]() |
Install the extension housing dynamic damper with the 4 bolts.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
| 3. INSTALL MANUAL TRANSMISSION ASSEMBLY |
Install the manual transmission assembly with the 9 bolts.

- Torque:
- 72 N*m{ 729 kgf*cm , 53 ft.*lbf }
- HINT:
- The A bolts in the illustration tighten the control cable bracket together.
- The A bolts in the illustration tighten the control cable bracket together.
- The B bolts in the illustration tighten the stiffener plate together.
- The B bolts in the illustration tighten the stiffener plate together.
- Bolt C in the illustration tightens the harness clamp bracket together.
- Bolt C in the illustration tightens the harness clamp bracket together.
Install the transmission assembly to the frame with the bolt, nut, and 2 washers.

- Torque:
- 98 N*m{ 999 kgf*cm , 72 ft.*lbf }
- NOTICE:
- Insert the bolt from the left side of the vehicle.
- Tighten the nut while holding the bolt.
- Insert the bolt from the left side of the vehicle.
| 4. INSTALL STARTER ASSEMBLY (for 2.2 kW Type) |
for Automatic Transmission:
Install the starter with the bolt and 2 nuts.
- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
for Manual Transmission:
Install the starter with the bolt and nut.
- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
Connect the wire harness to terminal 30 with the nut.
- Torque:
- 9.8 N*m{ 100 kgf*cm , 87 in.*lbf }
Close the terminal cap.
Connect the terminal 50 connector to the starter.
for Wide Body:
Install the ground cable with the bolt.- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
| 5. INSTALL STARTER ASSEMBLY (for 2.7 kW Type) |
for Automatic Transmission:

Install the starter with the bolt and 2 nuts.- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
for Manual Transmission:

Install the starter with the bolt and nut.- Torque:
- 68 N*m{ 693 kgf*cm , 50 ft.*lbf }
Connect the wire harness to terminal 30 with the nut.

- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Close the terminal cap.
Connect the terminal 50 connector to the starter.
for Wide Body:

Install the wire ground cable with the bolt.- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
| 6. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY |
Install the clutch release cylinder assembly with the 2 bolts.

- Torque:
- 12 N*m{ 119 kgf*cm , 8.6 ft.*lbf }
| 7. INSTALL WIRE HARNESS |
Connect the speed sensor connector.
Connect the back-up light switch connector.
Install the ground cable with the bolt.
- Torque:
- 13 N*m{ 130 kgf*cm , 10 ft.*lbf }
| 8. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
Install 2 new clips to the No. 1 transmission control cable bracket.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket.
- NOTICE:
- Make sure that A claws of the clips are firmly installed into the bracket grooves.
- Make sure that the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.
- Make sure that A claws of the clips are firmly installed into the bracket grooves.
Align the matchmarks on the control cable assembly and the shift outer lever.

Align the matchmarks on the control cable assembly and the select outer lever.
Install the transmission control cable assembly to the shift outer lever with the nut.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
Install the transmission control cable assembly to the select outer lever with the nut.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 9. INSTALL TRANSMISSION CONTROL CABLE INSULATOR (for RHD) |
Install the No. 1 transmission control cable insulator to the select outer lever with the nut.

- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
Install the No. 2 transmission control cable insulator to the No. 1 transmission control cable bracket with the 2 nut.
- Torque:
- 10 N*m{ 102 kgf*cm , 7 ft.*lbf }
| 10. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase) |
| 11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase) |
| 12. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/o DPF) |
Install a new gasket and the exhaust manifold converter sub-assembly with 3 new nuts.
- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
| 13. TEMPORARILY INSTALL TURBINE OUTLET ELBOW STAY |
w/ DPF:
Temporarily install the turbine outlet elbow stay with the 2 bolts.
w/o DPF:
Temporarily install the turbine outlet elbow stay with the 2 bolts and 2 new nuts.
Tighten the 2 bolts.
- Torque:
- 62 N*m{ 632 kgf*cm , 46 ft.*lbf }
| 14. INSTALL CATALYTIC WITH PIPE CONVERTER ASSEMBLY (w/ DPF) |
Install a new gasket and the catalytic with pipe converter assembly with 3 new nuts.

- Torque:
- 30 N*m{ 306 kgf*cm , 22 ft.*lbf }
Temporarily install 2 new nuts.
Tighten the 2 bolts of the turbine outlet elbow stay.
- Torque:
- 62 N*m{ 632 kgf*cm , 46 ft.*lbf }
| 15. INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF) |
Install the No. 3 exhaust manifold heat insulator with the 2 bolts.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
| 16. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF) |
Install the No. 2 exhaust manifold heat insulator with the 2 bolts.
- Torque:
- 13 N*m{ 133 kgf*cm , 10 ft.*lbf }
| 17. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ DPF) |
| 18. INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/o DPF) |
Inspect the compression spring.

Using a vernier caliper measure the free length of the compression spring.
- Minimum length:
- 40.5 mm (1.59 in.)
Fully push a new gasket onto the exhaust manifold converter sub-assembly by hand.

Text in Illustration *1
Gasket
*a
Wooden Block
Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold converter sub-assembly fit together properly.
- NOTICE:
- Install the gasket in the correct direction.
- Do not damage the outer surface of the gasket.
- Do not reuse the removed gasket.
- Do not push in the gasket with the front exhaust pipe assembly when connecting the pipe.
- Install the gasket in the correct direction.
Connect the front exhaust pipe assembly to the No. 4 exhaust pipe support.
Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts and 2 nuts.
- Torque:
- for bolt:
- 43 N*m{ 438 kgf*cm , 32 ft.*lbf }
- for nut:
- 48 N*m{ 489 kgf*cm , 35 ft.*lbf }
| 19. ADD MANUAL TRANSMISSION OIL |
Park the vehicle in a level place.

Remove the transmission filler plug and gasket.
Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.
- Oil grade:
- TOYOTA Genuine Manual Transmission Gear oil API GL-3 (GL-4) or equivalent
- Viscosity:
- Above -10°C (14°F): SAE 75W-90, 80W or 80W-90
- Below -10°C (14°F): SAE 75W-90
- Capacity:
- 2.6 liters (2.7 US qts, 2.3 Imp. qts)
- NOTICE:
- Problems may occur when the oil level is too high or too low.
- After replacing the oil, drive the vehicle and check the oil level again.
- Problems may occur when the oil level is too high or too low.
Check for oil leakage if the oil level is low.
Install the transmission filler plug and a new gasket.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 47 in.*lbf }
| 21. INSPECT FOR EXHAUST GAS LEAK |
| 22. INSPECT FOR OIL LEAK |
| 23. PERFORM INITIALIZATION |

