2014-2019 Hiace · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. DISCONNECT BATTERY NEGATIVE CABLE

2. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY

  1. C101767
    Remove the transmission oil level gauge sub-assembly from the transmission oil filler tube.


3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.2

4. REMOVE ENGINE UNDER COVER NO.1

5. DRAIN AUTOMATIC TRANSMISSION FLUID

  1. C101769E03
    Remove the drain plug and gasket and drain automatic transmission fluid.

  1. Install the drain plug with a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


6. REMOVE PROPELLER SHAFT ASSEMBLY

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  


7. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. Remove the 4 bolts, 2 nuts and 2 compression springs. 2 gasket and exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front and 2 gaskets.


8. REMOVE STARTER ASSEMBLY

  1. A113410E01
    for Wide Body:
    Remove the bolt, then disconnect the ground cable.

  1. A115882E01
    Open the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.

  1. A115883E01
    Remove the bolt and 2 nuts, then remove the starter.


9. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

  1. C101768E01
    Remove the 2 bolts transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.


10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C101771E02
    Remove the nut and disconnect transmission control cable assembly from the transmission control shaft lever assembly.

  1. Remove the clip and disconnect the transmission control cable assembly from the transmission control bracket.


11. DISCONNECT OIL COOLER TUBE

  1. Remove the 5 bolts and disconnect the 3 oil cooler tube clamps.

    C101770

  1. C158421
    Using a 17 mm union nut wrench, disconnect the 2 oil cooler tubes from the automatic transmission assembly.


12. DISCONNECT CONNECTOR

  1. w/ Speedometer Sensor:

    1. C157537E01
      Disconnect the speedometer sensor connector.

  1. C101772E02
    Disconnect the park/neutral position switch connector and temperature sensor connector.

  1. C101774E01
    Disconnect the speed sensor connector (SP2) and transmission wire connector.

  1. C101773E01
    Disconnect the speed sensor connector (NCO).


13. DISCONNECT WIRE HARNESS

  1. C101775E01
    Remove the 2 bolts and disconnect the wire harness from the automatic transmission assembly.


14. REMOVE CYLINDER BLOCK INSULATOR NO.4

  1. C101776E01
    Remove the cylinder block insulator No.4.


15. REMOVE STIFFENER PLATE RH(ATM)

  1. C230787
    Remove the 3 bolts and stiffener plate RH.


16. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

  1. C101778E01
    Remove the bolt and drive plate cover from the automatic transmission assembly.

  1. C101779
    Turn the crankshaft pulley and remove the 6 torque converter clutch setting bolts.


17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

  1. C160266
    Support the automatic transmission assembly with a transmission jack.

    NOTICE:
    Ensure that the jack is positioned on the bolt heads and not directly on the oil pan itself.


18. DISCONNECT ENGINE MOUNTING INSULATOR ASSEMBLY REAR

  1. C101781
    Remove the bolt, nut and washer and disconnect the engine mounting insulator assembly rear.


19. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

  1. C101782
    Remove the 5 bolts and automatic transmission assembly.


20. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1

  1. C101783
    Remove the 2 bolts and transmission control cable bracket No.1 from the automatic transmission assembly.


21. REMOVE ENGINE MOUNTING INSULATOR ASSEMBLY REAR

  1. C101785
    Remove the 4 bolts and engine mounting insulator assembly rear from the automatic transmission assembly.


22. REMOVE BREATHER PLUG HOSE

  1. C101784
    Remove the bolt and breather plug hose from the automatic transmission assembly.


23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

  1. C108498E01
    Put a matchmarks on the transmission case and the torque converter assembly.

  1. Remove the torque converter assembly from the automatic transmission assembly.


24. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

  1. D029377E02
    Inspect the one-way clutch.

    1. Install the SST so that it fits in the notch of the converter hub and the outer race of the one-way clutch.

      SST
      09350-32014   (09351-32010, 09351-32020)

    2. Install the SST (Stopper) from the sleeve of torque converter assembly and engage serration of stater slight washer.

    3. Stand up the torque converter and turn the SST (tool ).

      SST
      09350-32014   (09351-32010, 09351-32020)

      Standard:
      Check if it rotates smoothly when turned clockwise and locks up when turned counter clockwise.

  1. D025367E01
    Determine the condition of the torque converter clutch assembly.

    1. If the inspection result of the torque converter clutch assembly meets the following item, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in the N position.
      The one-way clutch is free or locked in both directions.
      Fine powder exceeding the sample limit is identified in ATF. (See the sample.)

      HINT:
      1. The sample shows the auto fluid of approximately 0.25 liters (0.26 US qts, 0.22 Imp, qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation face up.

  1. C011090
    Clean and check the oil cooler and oil pipe line.

    1. If the torque converter clutch is inspected or exchange the ATF, is exchanged, clean the oil cooler and oil pipe line.

      HINT:
      1. Spray compressed air of 196 kPa (2kgf/cm2, 28 psi) from the inlet hose.
      2. If plenty of fine powders are identified in the ATF, add a new ATF using a bucket pump and clean it again.

    2. If the ATF is cloudy, inspect the oil cooler.

← COMPONENTS (from Dec 2017)INSTALLATION (Oct 2014 – Dec 2014) →