2014-2019 Hiace · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. DISCONNECT BATTERY NEGATIVE TERMINAL CABLE

2. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY

  1. C102919
    Remove the transmission oil level gage sub assembly from the transmission oil filler tube.


3. REMOVE ENGINE UNDER COVER SUB-ASSEMBLY NO.2

4. REMOVE ENGINE UNDER COVER NO.1

5. REMOVE ENGINE SIDE UNDER COVER LH

6. REMOVE ENGINE SIDE UNDER COVER RH

7. DRAIN AUTOMATIC TRANSMISSION FLUID

  1. C101769E01
    Drain the automatic transmission fluid and remove the drain plug and gasket.

  1. Install the drain plug with a new gasket.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


8. REMOVE PROPELLER SHAFT ASSEMBLY

  1. C102185E01
    Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

  1. Remove the propeller shaft assembly.

  1. C102186E01
    Insert SST in the transmission to prevent oil leakage.

    NOTICE:
    Do not damage the oil seal.


    1. Use the following SST for the automatic transmission

      SST
      09325-40010  

    2. Use the following SST for the manual transmission

      SST
      09325-20010  


9. REMOVE EXHAUST PIPE ASSEMBLY FRONT
  1. w/ Secondary air injection system:

    1. Disconnect the fuel ratio sensor connector.

    2. Remove the fuel ratio sensor. (Click here)

  1. For unleaded gasoline engine:

    1. Disconnect the oxygen sensor connector.

    2. Remove the oxygen sensor. (Click here)

  1. Remove the 4 bolts, 2 nuts, and 2 compression springs.

  1. Remove the 2 gaskets from the exhaust pipe assembly front.

  1. Disconnect the exhaust pipe support, and remove the exhaust pipe assembly front.


10. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

  1. C102934E01
    Remove the 2 bolts transmission oil filler tube sub-assembly.

  1. Remove the O-ring from the oil filler tube sub-assembly.


11. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C102933E05
    Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever assembly.

  1. Remove the clip and disconnect the transmission control cable assembly from the transmission control cable bracket.


12. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1

  1. C102931E02
    Remove the 2 bolts and transmission control cable bracket to the automatic transmission assembly.


13. REMOVE STARTER ASSEMBLY

  1. A102709E01
    Remove the 2 bolts, then remove the ground cable and bracket.

  1. A113538E02
    Remove the nut and disconnect the wire harness from terminal 30.

  1. Disconnect the terminal 50 connector from the starter assembly.

  1. Remove the 2 bolts and the starter assembly.


14. DISCONNECT OIL COOLER TUBE

  1. Remove the 3 bolts and disconnect the 3 cooler tube clamps.

    C102932

  1. C102930E01
    Using a 17 mm union nut wrench, disconnect the 2 oil cooler tubes from the automatic transmission assembly.


15. DISCONNECT CONNECTOR

  1. C101834E03
    Remove the heat insulator from the park/neutral position switch assembly with 2 bolts.

  1. C102929E04
    Disconnect the park/neutral position switch connector.

  1. C101774E02
    Disconnect the connector of speed sensor (SP2) connector and transmission wire connector.

  1. C102928E01
    Disconnect the connector of speed sensor (NCO) connectorand temperature sensor.


16. DISCONNECT WIRE HARNESS

  1. C102927E01
    Remove the 3 bolts and disconnect the wire harness from the automatic transmission assembly .


17. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

  1. C102926E01
    Remove the flywheel housing dust seal from the automatic transmission assembly.

  1. C102925E01
    Remove the torque converter clutch setting bolts with 6 bolts.


18. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

  1. C102924E01
    Support the automatic transmission assembly with a transmission jack.


19. DISCONNECT ENGINE MOUNTING INSULATOR ASSEMBLY REAR

  1. C101781
    Disconnect the engine mounting insulator assembly rear with bolt, nut and 2 washers.


20. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

  1. C103762
    Remove the automatic transmission assembly with 8 bolts.


21. REMOVE ENGINE MOUNTING INSULATOR ASSEMBLY REAR

  1. C102922E01
    Remove the 4 bolts and engine mounting insulator assembly rear from the automatic transmission assembly.


22. REMOVE BREATHER PLUG HOSE

  1. C103234E01
    Remove the breather plug hose from the automatic transmission assembly with a bolt.


23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

  1. C101843E02
    Put matchmarks on the transmission case and torque converter assembly.

  1. Remove the torque converter assembly from the automatic transmission assembly.


24. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

  1. D029377E02
    Inspect the one-way clutch.

    1. Install the SST so that it fits in the notch of the converter hub and the outer race of the one-way clutch.

      SST
      09350-32014   (09351-32010, 09351-32020)

    2. Install the SST (Stopper) from the sleeve of torque converter assembly and engage serration of stater slight washer.

    3. Stand up the torque converter and turn the SST (tool ).

      SST
      09350-32014   (09351-32010, 09351-32020)

      Standard:
      Check if it rotates smoothly when turned clockwise and locks up when turned counter clockwise.

  1. D025367E01
    Determine the condition of the torque converter clutch assembly.

    1. If the inspection result of the torque converter clutch assembly meets the following item, replace the torque converter clutch.

      Malfunction item:
      Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in the N position.
      The one-way clutch is free or locked in both directions.
      Fine powder exceeding the sample limit is identified in ATF. (See the sample.)

      HINT:
      1. The sample shows the auto fluid of approximately 0.25 liters (0.26 US qts, 0.22 Imp, qts) that is taken out from the removed torque converter clutch.

  1. Replace the ATF in the torque converter clutch.

    1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation face up.

  1. C011090
    Clean and check the oil cooler and oil pipe line.

    1. If the torque converter clutch is inspected or exchange the ATF, is exchanged, clean the oil cooler and oil pipe line.

      HINT:
      1. Spray compressed air of 196 kPa (2kgf/cm2, 28 psi) from the inlet hose.
      2. If plenty of fine powders are identified in the ATF, add a new ATF using a bucket pump and clean it again.

    2. If the ATF is cloudy, inspect the oil cooler.

← COMPONENTS (from Dec 2017)INSTALLATION (Oct 2014 – Dec 2014) →