2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014


1. TEMPORARILY TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY

  1. Temporarily tighten the EGR valve assembly with the sensor.

    1. A115761E01
      Install 2 new gaskets and the EGR valve to the intake air connector as shown in the illustration.

    2. A102287
      Temporarily tighten the intake air connector with EGR valve assembly to the intake manifold with the bolt and the 2 nuts.

    3. Install the vacuum hose to the intake air connector.

    4. Temporarily tighten the manifold stay with the bolt.

    5. A103043
      Connect the EGR valve position sensor connector.

    6. Connect the intake air temperature sensor connector.

  1. Install the vacuum regulating valve.

    1. A103046
      Install the vacuum regulating valve with the 2 bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Connect the 2 vacuum hoses and the regulating valve connector.


2. INSTALL EGR PIPE SUB-ASSEMBLY NO.1

  1. A106845
    Install the 2 gaskets to the cylinder head and EGR pipe sub-assembly as shown in the illustration.

  1. A106844
    Install the EGR pipe sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the intake air connector with the bolt and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the manifold stay.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


3. REMOVE EGR PIPE SUB-ASSEMBLY NO.1
  1. Remove the 3 bolts, the 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.


4. INSTALL DIESEL THROTTLE BODY ASSEMBLY

NOTICE:
After removing and installing, or replacing the throttle body, be sure to perform the operation check.

  1. Install a new gasket to intake air connector.

  1. A102902
    Install the throttle body with the 2 bolts and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A102282
    Connect the 2 throttle body connectors.


5. INSTALL AIR HOSE NO.4

  1. A102281
    Install the air hose No.4 with the 2 clamps.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


6. INSTALL EGR PIPE SUB-ASSEMBLY NO.1

  1. A106845
    Install 2 new gaskets to the cylinder head and the EGR pipe sub-assembly No.1 as shown in the illustration.

  1. A106844
    Install the EGR pipe with the 2 bolts and the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A106043
    Connect the fuel pressure sensor connector.


7. CONNECT OIL RETURN HOSE (w/ Intercooler)

  1. A106042
    Connect the oil return hose with the clip.


8. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

  1. C101999E01
    Install the vane pump oil reservoir assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


9. INSTALL ENGINE SERVICE HOLE COVER NO.2
  1. Install the engine service hole cover No.2 with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A113039
    Return the carpet.


10. CHECK FUNCTION OF THROTTLE BODY
(Click here)

11. INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }

← INSPECTION (from Oct 2014)INSPECTION (from Oct 2014) →