2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Oct 2014


1. REMOVE ENGINE ASSEMBLY
(Click here)

2. REMOVE VANE PUMP ASSEMBLY

  1. C101372E01
    Remove the 2 nuts and the vane pump assembly.

  1. Remove the vane pump O-ring from the vane pump assembly.


3. REMOVE TIMING BELT COVER NO.1
  1. Remove the wire harness clamp.

  1. A102815
    Remove the 6 bolts and timing belt cover No.1.


4. REMOVE TIMING BELT

  1. A070549E01
    Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.

  1. A070550
    Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.

  1. Remove the timing belt.


5. REMOVE FAN PULLEY
  1. Remove the 4 nuts and fan pulley.


6. REMOVE EGR PIPE SUB-ASSEMBLY NO.1

  1. A106043
    Disconnect the fuel pressure sensor connector.

  1. A106844
    Remove the 2 bolts, 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.


7. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the oil level gauge.

  1. Remove the bolt and oil level gauge guide.


8. REMOVE INJECTION PIPE
SST
09023-12701  

  1. Remove the injection pipe.

    1. A103526
      Remove the 2 nuts and injection pipe clamp No.3.

    2. A103532
      Using SST, remove the 4 injection pipes.
      SST
      09023-12701  


9. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Using SST, remove the fuel inlet pipe sub-assembly.

    SST
    09023-12701  


10. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY

  1. A070710
    Remove the 4 bolts.

  1. Remove the camshaft timing pulley flange No.2 and pump drive shaft pulley.

  1. A077989
    Using SST, remove the supply pump gear set nut and O-ring while holding the crankshaft pulley.
    SST
    09213-58013  
    09330-00021  

  1. A076978
    Disconnect the 2 fuel hoses.

  1. Disconnect the 2 connectors and wire harness.

  1. Loosen the 2 nuts as shown in the illustration.

  1. A077990E01
    Using SST, disengage the supply pump from the supply pump gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

  1. Remove the 2 nuts and supply pump from the engine.

  1. Remove the O-ring from the supply pump.

  1. Remove the pulley key from the supply pump.


11. REMOVE COMPRESSOR BRACKET

  1. A102453E01
    Remove the 4 bolts and compressor bracket.


12. REMOVE IDLE PULLEY ASSEMBLY
  1. Remove the bolt, washers and idle pulley assembly.


13. REMOVE GENERATOR BRACKET
  1. Remove the 2 bolts and generator bracket.


14. REMOVE GENERATOR ASSEMBLY

  1. A113682E01
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and generator assembly.


15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Remove the 4 bolts and belt tensioner assembly.


16. REMOVE TIMING BELT IDLER SUB-ASSEMBLY NO.1

  1. A070696
    Using a 10 mm socket hexagonal wrench, remove the bolt, plate washer and timing belt idler No.1.


17. REMOVE CRANKSHAFT PULLEY

  1. A072413E01
    Remove the bolt holding the crankshaft with SST.
    SST
    09213-58013  
    09330-00021  

  1. Insert the service bolt.

  1. A072414E01
    Remove the crankshaft pulley with SST.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


18. REMOVE VACUUM PUMP ASSEMBLY

  1. C102554
    Slide the clip and disconnect the 2 vacuum hoses from the vacuum pump.

  1. Remove the union bolt, vacuum pump union and 2 gaskets.

  1. C102555
    Remove the 2 nuts and pull out the vacuum pump from the engine.

  1. Remove the 2 O-rings.


19. REMOVE CAMSHAFT POSITION SENSOR

  1. A102283
    Disconnect the camshaft position sensor connector.

  1. Remove the bolt and the camshaft position sensor.


20. REMOVE CRANKSHAFT POSITION SENSOR

  1. A102284
    Disconnect the crankshaft position sensor connector.

  1. Separate the connector from the vacuum pipe No.1.

  1. A102285
    Separate the 3 wire harness clamps.

  1. Remove the bolt and the crankshaft position sensor.


21. REMOVE ENGINE OIL LEVEL SENSOR
  1. Remove the 4 bolts and engine oil level sensor.


22. REMOVE OIL FILLER CAP SUB-ASSEMBLY

  1. A074130
    Remove the oil filler cap from the cylinder head cover.


23. REMOVE NOZZLE HOLDER SEAL

  1. A100846
    Using a screwdriver, remove the holder seals by prying the portion between the holder seal and the cutout part of the cylinder head.


24. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A051295E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and the cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


25. REMOVE CAMSHAFT TIMING PULLEY

  1. A100848
    Remove the bolt for the camshaft timing pulley by holding the camshaft with a wrench.

  1. A323634E01
    Using SST, remove the camshaft timing pulley and set key.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-05010, 09957-04010)
    09955-04150  

  1. A100847E05
    Rotate the crankshaft about 90° counterclockwise from the TDC position to lower the piston.


26. REMOVE TIMING BELT COVER NO.2

  1. A051300
    Remove the nut, 4 bolts and timing belt No.2 cover.


27. REMOVE WATER PUMP ASSEMBLY

  1. A100852
    Remove the 5 bolts, 2 nuts, water pump and gasket.


28. REMOVE TIMING GEAR CASE

  1. A100853
    Remove the 14 bolts and 2 nuts.

  1. A102800
    Pry the gear case in the location shown in the illustration.

    NOTICE:
    Do not damage the contact surface.

  1. A102771
    Secure the idler sub-gears to the idler gear with a service bolt.

  1. A102772
    Remove the supply pump gear.

  1. A103311E01
    Remove the O-ring.


29. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO.1

  1. A102774
    Remove the crankshaft position sensor plate.


30. REMOVE CRANKSHAFT TIMING GEAR

  1. A100863E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)


31. REMOVE IDLE GEAR THRUST PLATE

  1. A102775
    Remove the 2 bolts and thrust plate.


32. REMOVE IDLE GEAR NO.1

  1. A100860
    Turn the sub gear and align the gear teeth of the idle main gear and sub gear.

  1. Remove the idle gear and sub gear.


33. REMOVE IDLE GEAR SHAFT NO.1

  1. A102776
    Remove the idle gear shaft.


34. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

  1. A100854
    Using a screwdriver and hammer, tap out the oil seal.


35. REMOVE TIMING CHAIN OR BELT COVER OIL SEAL

  1. A100856
    Using a screwdriver and hammer, tap out the oil seal.


36. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and gasket.

  1. A074128E01
    Remove the 22 bolts and 2 nuts.

  1. Z004119E01
    Insert the blade of SST between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use SST for the timing belt case side and rear oil seal retainer.
    2. Do not damage the oil pan flange.


37. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A102736
    Remove the 2 bolts, 2 nuts, oil strainer and gasket.


38. REMOVE TIMING GEAR CASE ASSEMBLY

  1. A100878
    Remove the union bolt and 8 bolts.

  1. A102853E01
    Pry the gear case in the location shown in the illustration, remove the gear case.

    NOTICE:
    Do not drop the oil pump rotor.

  1. A051330
    Remove the driven rotor and gasket.

  1. A052300
    Remove the stud bolt.

  1. A102777
    Remove the 2 O-rings.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →