2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


1. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)

2. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
(Click here)

3. REMOVE INTAKE MANIFOLD
(Click here)

4. REMOVE EXHAUST MANIFOLD
(Click here)

5. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the crankshaft pulley bolt.

  1. A252704E02
    Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.
    Text in Illustration 
    *1
    Key
    *a
    Timing Mark

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.


6. REMOVE TIMING CHAIN GUIDE

  1. A101304E03
    Remove the 2 bolts, timing chain guide and O-ring.
    Text in Illustration 
    *1
    O-Ring


7. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
  1. When the No. 1 chain tensioner assembly is removed, do not rotate the crankshaft.
  2. When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.

  1. A101303E14
    Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *a
    Stopper Plate
    *b
    Hexagon Wrench

  1. Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.

  1. Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.


8. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the bolt and chain tensioner slipper.


9. REMOVE NO. 1 CHAIN VIBRATION DAMPER
  1. Remove the 2 bolts and No. 1 chain vibration damper.


10. REMOVE CHAIN SUB-ASSEMBLY

11. REMOVE CAMSHAFT BEARING CAP

  1. A170574E03
    Uniformly loosen and remove the 21 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshafts level.

  1. A101310
    Remove the oil delivery pipe and O-ring from the bearing caps.

  1. A101311E02
    Remove the 9 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.


12. REMOVE CAMSHAFT

  1. A101312
    Remove the camshaft.


13. REMOVE NO. 2 CAMSHAFT

  1. A101313
    Remove the No.2 camshaft.


14. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 16 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

    HINT:
    Arrange the removed parts in the correct order.


15. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

    HINT:
    Arrange the removed parts in the correct order.


16. REMOVE VALVE STEM CAP
  1. Remove the 16 valve stem caps from the cylinder head sub-assembly.

    HINT:
    Arrange the removed parts in the correct order.


17. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. A101319E04
    Uniformly loosen the 10 bolts in the sequence shown in the illustration. Remove the 10 cylinder head set bolts and plate washers.

    NOTICE:
    1. Be careful not to drop plate washers into the cylinder head sub-assembly.
    2. Head warpage or cracking could result from removing bolts in incorrect order.

  1. Remove the cylinder head sub-assembly.


18. REMOVE CYLINDER HEAD GASKET

19. INSPECT CYLINDER HEAD SET BOLT

  1. A170594E03
    Using a vernier caliper, measure the diameter of the most elongated threads in the measuring area.

    Standard outside diameter:
    10.76 to 10.97 mm (0.424 to 0.432 in.)

    Minimum outside diameter:
    10.40 mm (0.409 in.)

    Distance:
    30 mm (1.18 in.)

    Text in Illustration 
    *a
    Measuring area
    *b
    Distance
    If a visual check reveals no excessively thin areas, check the center of the measuring area (see illustration) and find the area that has the smallest diameter.
    If the diameter is less than the minimum, replace the cylinder head set bolt.


20. INSPECT CYLINDER HEAD SUB-ASSEMBLY

  1. A101375E02
    Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder block and manifolds.

    Maximum warpage:
    0.05 mm (0.00197 in.)

    Text in Illustration 
    *a
    Cylinder Head Lower Side
    *b
    Intake Manifold Side
    *c
    Exhaust Manifold Side
    If the warpage is more than the maximum, replace the cylinder head sub-assembly.

  1. Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
    If cracked, replace the cylinder head sub-assembly.

← COMPONENTS (from Jan 2015)REMOVAL (from Jan 2015) →