2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE FAN AND GENERATOR V BELT
(Click here)

5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the engine coolant in a container and dispose of it according to the local regulations.

  1. Loosen the radiator drain cock plug and drain the engine coolant.

    A316605E01

    Text in Illustration 
    *1
    Radiator Reservoir Cap Sub-assembly
    *2
    Radiator Reservoir Assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Water Drain Cock Plug
    *5
    2-Way
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block water drain cock plug and drain the engine coolant from the engine.


6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    NOTICE:
    Collect the oil in a disposable oil container.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }


7. REMOVE CAMSHAFT POSITION SENSOR

  1. A086888
    Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.


8. DISCONNECT NO. 2 RADIATOR HOSE
  1. Slide the clamp and disconnect the No. 2 radiator hose from the No. 1 radiator pipe.


9. DISCONNECT NO. 4 RADIATOR HOSE
  1. Slide the clamp and disconnect the No. 4 radiator hose from the engine.


10. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

  1. A103325
    Slide the clamp and disconnect the fuel vapor feed hose from the purge VSV.


11. DISCONNECT UNION TO CONNECTOR TUBE HOSE
  1. Slide the clamp and disconnect the union to connector tube hose from the intake manifold.


12. REMOVE INTAKE AIR CONNECTOR

  1. A102437
    Slide the clamp and disconnect the No. 2 PCV hose from the cylinder head cover sub-assembly.

  1. Disconnect the vacuum hose from the intake air connector.

  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts and intake air connector.


13. DISCONNECT NO. 1 FUEL HOSE

  1. A309365
    Disconnect the No. 1 fuel hose from the fuel pressure pulsation damper assembly (Click here).


14. DISCONNECT NO. 2 FUEL HOSE
  1. Disconnect the No. 2 fuel hose from the fuel delivery pipe sub-assembly (Click here).


15. DISCONNECT VANE PUMP ASSEMBLY

  1. A102130E01
    Disconnect the oil pressure switch connector.

  1. Remove the 2 bolts and disconnect the vane pump assembly from the engine.

  1. Support the vane pump assembly securely.


16. REMOVE ENGINE OIL LEVEL DIPSTICK

17. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A102132E01
    Remove the bolt, engine oil level dipstick guide and O-ring.


18. DISCONNECT COMPRESSOR AND MAGNETIC CLUTCH
  1. Disconnect the compressor and magnetic clutch connector.

  1. A102804E02
    Remove the 4 bolts and disconnect the compressor and magnetic clutch from the engine.

    HINT:
    Disconnect the compressor and magnetic clutch with the No. 1 cooler refrigerant suction hose and No. 1 cooler refrigerant discharge hose stuck by suspended from the rope.

  1. Support the compressor and magnetic clutch securely.


19. DISCONNECT ENGINE WIRE
  1. Disconnect the wire harness support of the ECM.

  1. Disconnect the connectors of the ECM.

  1. Disconnect the clamps of the engine wire and ground cable.

  1. Disconnect the starter connector (Click here).

  1. Disconnect the generator connector (Click here).

  1. A101143E05
    Remove the nut and disconnect the 4 connectors from the engine room junction block.
    Text in Illustration 
    *1
    Nut


20. REMOVE THROTTLE WITH MOTOR BODY ASSEMBLY

  1. A272177
    Disconnect the throttle motor connector.

  1. Slide the clamp and disconnect the water by-pass hose from the throttle body.

  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the throttle body.

  1. Remove the 4 bolts and throttle body assembly.

  1. A239457
    Remove the gasket from the intake manifold.


21. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

NOTICE:
Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

  1. Disconnect the vacuum hose from the fuel pressure regulator assembly.

  1. Slide the clamp and disconnect the No. 2 fuel hose from the fuel pressure regulator assembly.

  1. A313560
    Disconnect the 4 fuel injector connectors.

  1. Remove the 2 bolts, fuel pressure pulsation damper assembly and O-ring.

  1. Remove the 2 bolts and fuel delivery pipe sub-assembly together with the 4 fuel injector assemblies.

    NOTICE:
    Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.

  1. Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.

  1. Remove the 4 injector vibration insulators.

  1. A313561
    Using a screwdriver, pry out the 4 injector spacers and 4 O-rings from the cylinder head sub-assembly.


22. REMOVE INJECTOR ASSEMBLY

  1. A223378
    Pull out the 4 fuel injector assemblies from the fuel delivery pipe sub-assembly.
    Text in Illustration 
    V100135
    Pull Out

  1. Remove the O-rings from the fuel injector assemblies.


23. REMOVE INTAKE MANIFOLD
  1. Disconnect the vacuum switching valve connector.

  1. Slide the clamp and disconnect the purge line hose from the vacuum switching valve.

  1. A110725
    Detach the 2 wire harness clamps from the wire harness bracket.

  1. Slide the clamp and disconnect the No. 3 PCV hose from the intake manifold.

  1. Slide the clamp and disconnect the vacuum hose from the intake manifold.

  1. A110726
    Remove the bolt and wire harness bracket from the intake manifold.

  1. A239455
    Remove the 5 bolts, 2 nuts and intake manifold.

  1. Remove the gasket from the intake manifold.


24. REMOVE FAN PULLEY
  1. Remove the 4 nuts, fan pulley and fan spacer.


25. REMOVE NO. 1 WATER BY-PASS PIPE
  1. Remove the bolt, 2 nuts, water by-pass pipe and gasket.


26. REMOVE WATER INLET

  1. A087301
    Remove the 2 nuts and bolt and disconnect the water inlet.

  1. Remove the gasket.


27. REMOVE THERMOSTAT

  1. A086841J01
    Remove the thermostat and gasket.


28. REMOVE GENERATOR ASSEMBLY

  1. A311548
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Remove the bolt and disconnect the wire harness clamp.

  1. A311549
    Remove the 3 bolts and generator assembly.


29. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

  1. A337819
    Remove the 5 bolts and No. 1 compressor mounting bracket.


30. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

  1. A102170
    Remove the bolt, pulley plate, collar and No. 1 idler pulley sub-assembly.


31. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A232341
    Remove the 2 bolts and V-ribbed belt tensioner assembly.


32. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 4 bolts and 4 ignition coil assemblies.


33. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A101292
    Remove the 19 bolts, 2 nuts and cylinder head cover sub-assembly.

  1. Remove the cylinder head cover gasket and No. 2 cylinder head cover gasket from the cylinder head cover sub-assembly.


34. REMOVE CRANKSHAFT POSITION SENSOR

  1. G037913
    Disconnect the crankshaft position sensor connector and detach the 2 wire harness clamps.

  1. G037914
    Remove the bolt and crankshaft position sensor.


35. REMOVE CRANKSHAFT PULLEY

  1. A101288E03
    Using SST, hold the crankshaft pulley and loosen the pulley bolt until 2 or 3 threads are screwed into the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  
    Text in Illustration 
    *a
    Loosen
    *b
    Hold

  1. A101289E04
    Using SST and the pulley bolt, remove the crankshaft pulley and pulley bolt.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    HINT:
    Apply lubricant to the threads and end of SST.


36. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove the oil pan drain plug and gasket.

  1. A101291
    Remove the 18 bolts and 2 nuts.

  1. A101293
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Do not damage the contact surfaces of the oil pans.


37. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A101294E03
    Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.


38. REMOVE OIL PAN SUB-ASSEMBLY

  1. A264837E01
    Remove the 16 bolts and 2 nuts.

  1. A101296E04
    Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block with a screwdriver.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not damage the contact surfaces of the cylinder block and oil pan sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. A101297E01
    Remove the O-ring.


39. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. A309164
    Remove the 17 bolts and nut shown in the illustration.

  1. A101299E03
    Remove the timing chain or belt cover sub-assembly by prying between the timing chain or belt cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain or belt cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. A222350E01
    Remove the 3 O-rings from the timing chain or belt cover sub-assembly.
    Text in Illustration 
    *1
    Timing Chain Cover O-ring
    *2
    Water Pump O-ring
    *3
    Oil Pump O-ring

  1. A101979
    Using a 10 mm socket hexagon wrench, remove the timing chain cover plug from the timing chain or belt cover sub-assembly.


40. REMOVE ENGINE WATER PUMP ASSEMBLY

  1. A101301
    Remove the 8 bolts, engine water pump assembly and gasket from the timing chain or belt cover sub-assembly.


41. REMOVE TIMING CHAIN CASE OIL SEAL

  1. A101302E05
    Using a screwdriver, pry out the timing chain case oil seal from the timing chain or belt cover sub-assembly.
    Text in Illustration 
    *a
    Protective Tape
    *b
    Wooden Block

    HINT:
    Tape the screwdriver tip before use.


42. REMOVE OIL PUMP RELIEF VALVE

  1. A086864
    Using a 27 mm socket wrench, remove the plug and gasket.

  1. Remove the relief valve spring and oil pump relief valve from the timing chain or belt cover sub-assembly.

← COMPONENTS (from Jan 2015)REMOVAL (Jan 2015 – Mar 2016) →