2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. INSTALL ENGINE OIL LEVEL SENSOR
  1. Install the engine oil level sensor with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 52 in.*lbf }


2. INSTALL ENGINE MOUNTING BRACKET FRONT NO.1 LH

  1. A102169
    Install the mounting bracket with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }


3. INSTALL ENGINE MOUNTING BRACKET FRONT NO.1 RH

  1. A102168
    Install the mounting bracket with the 4 bolts.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }


4. INSTALL WATER TEMPERATURE SENSOR

  1. A102134
    Using a 19 mm deep socket wrench, install a new gasket and the water temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


5. INSTALL KNOCK CONTROL SENSOR

  1. A087061
    Install the bolt and knock control sensor as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the knock control sensor connector.


6. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

  1. G036762E01
    Apply adhesive to 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. A102133
    Install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation of the switch.


7. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A232341E01
    Temporarily install the belt tensioner with the 2 bolts.

    HINT:
    1. Make sure that the belt tensioner is in contact with the engine block.
    2. Check that the bolt holes of the belt tensioner and timing chain cover are aligned.

  1. Install the tensioner by tightening the 2 bolts in the order shown in the illustration.

    Torque:
    Bolt 1:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }
    Bolt 2:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


8. INSTALL IDLER PULLEY SUB-ASSEMBLY NO.1

  1. A102170
    Install the idler pulley sub-assembly No.1, collar and pulley plate with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    NOTICE:
    Check that the pulley plate and collar are assembled properly to the idler pulley No.1.


9. INSTALL COMPRESSOR MOUNTING BRACKET NO.1 (w/ Air Conditioning System)

NOTICE:
Install the compressor mounting bracket No. 1 exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.

  1. A332607
    Temporarily install the compressor mounting bracket No. 1 with the 3 bolts.

    HINT:
    Temporarily install the compressor mounting bracket No. 1 with the 3 bolts so that the bracket can be moved by hand.

  1. Push the compressor mounting bracket No. 1 toward the cylinder block as shown in the illustration and tighten bolt B.

    A337822E01

    Torque:
    Bolt B:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

    HINT:
    Make sure there is no clearance between the cylinder block and compressor mounting bracket No. 1 as shown in the illustration.

  1. A337823E01
    Uniformly tighten the 4 bolts in the order shown in the illustration.

    Torque:
    Bolt A:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }
    Bolt C:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


10. INSTALL IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)
  1. Temporarily install the idle pulley assembly with the bolt.

    NOTICE:
    Do not use any tools.

  1. Tighten the bolt.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


11. INSTALL GENERATOR ASSEMBLY

  1. A088507E01
    Install the generator assembly with the 3 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the generator wire with the nut to terminal B.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the generator connector.


12. INSTALL THERMOSTAT
  1. Install a new gasket to the thermostat.

  1. A103361E01
    Install the thermostat with the jiggle valve upward.

    HINT:
    The jiggle valve may be set within 10° of either side of the prescribed position.


13. INSTALL WATER INLET
  1. Install a new gasket and the water inlet with the bolt and 2 nuts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }


14. INSTALL WATER BY-PASS PIPE NO.1
  1. Install a new gasket and the water by-pass pipe with the 2 nuts and bolt.

    Torque:
    Nut:
    18 N*m{ 180 kgf*cm , 13 ft.*lbf }
    Bolt:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }


15. INSTALL FAN PULLEY
  1. Install the fan spacer and fan pulley with the 4 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


16. INSTALL EXHAUST MANIFOLD

  1. A112543E02
    w/o Secondary air injection system:

    1. Install a new gasket and the exhaust manifold with the new 6 nuts.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. w/ Secondary air injection system:

    1. Install a new gasket and the exhaust manifold with the new 8 nuts.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }


17. INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

  1. A099545E02
    Install the valve with the 2 new nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the connector.

  1. A264866E01
    w/ Manifold Absolute Pressure Sensor:
    Connect the vacuum hose to the air switching valve assembly.


18. INSTALL INTAKE PIPE NO.4 (w/ Secondary Air Injection System)

  1. A099544E04
    Install 2 new gaskets and the intake pipe No.4 with 4 new nuts and tighten the nuts in the order shown in the illustration. Then, tighten the nuts labeled 1 and 3 to the torque specification again.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Check that the nuts are tightened to the torque specification.

    NOTICE:
    Tightening the nuts only once is not enough to tighten them to the torque specification.


19. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.1

  1. A113523
    Install the heat insulator with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


20. INSTALL INJECTOR ASSEMBLY
  1. Apply a light coat of grease or gasoline to new O-rings and install them to the injector spacers.

    NOTICE:
    Make sure that the O-rings are installed between the parts correctly.

  1. Install the injection spacers.

  1. Apply a light coat of grease or gasoline to the place where the delivery pipe touches the O-ring.

  1. A087155
    To install the fuel injector into the fuel delivery pipe, push the fuel injector while twisting it right and left.

    NOTICE:
    1. Be careful not to twist the O-ring.
    2. After installing the fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.


21. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. G036023
    Install the 4 spacers to the cylinder head.

  1. Install the delivery pipe spacers.

  1. A087154
    Temporarily install the 2 bolts and fuel delivery pipe together with the 4 injectors.

    NOTICE:
    1. Do not drop the fuel injector when installing the fuel delivery pipe.
    2. Make sure that the fuel injector turns smoothly.

  1. Fully tighten the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 10 ft.*lbf }

  1. Apply a light coat of grease or gasoline to the place where the delivery pipe touches the O-ring.

  1. Install the 2 bolts and pressure pulsation damper assembly.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the 2 fuel hoses.


22. INSTALL SPARK PLUG

Torque:
18 N*m{ 184 kgf*cm , 13 ft.*lbf }


23. INSTALL IGNITION COIL ASSEMBLY
  1. Install the ignition coils with the bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


24. INSTALL INTAKE MANIFOLD

  1. A102806
    Install a new gasket and the intake manifold with the 5 bolts and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the ventilation hose No.3.


25. INSTALL THROTTLE BODY ASSEMBLY

  1. A102440E01
    Install a new gasket onto the intake manifold.

    HINT:
    Fit the gasket to the cutout of the intake manifold.

  1. A102438E02
    for Type A:
    Install the throttle body assembly with the 2 bolts and 2 nuts. (A)

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. for Type B:
    Install the throttle body assembly with the 4 bolts. (A)

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the water by-pass hose, and slide the clamp to secure it. (B)

  1. Connect the No. 2 water by-pass hose, and slide the clamp to secure it. (C)

  1. Connect the throttle motor connector. (D)


26. INSTALL VENTILATION PIPE
  1. Install the ventilation pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


27. INSTALL ENGINE WIRE
  1. Install the engine wire to the engine assembly.


28. REMOVE ENGINE STAND

29. INSTALL FRONT SUSPENSION CROSS MEMBER SUB-ASSEMBLY
  1. Install the engine assembly to the cross member.

  1. Connect the engine mounting insulator with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }


30. INSTALL REAR END PLATE
  1. Install the rear end plate with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


31. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

HINT:
If any one of the mounting bolts is broken or deformed, replace it.

  1. A004869E01
    Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the flywheel.

  1. A102138E01
    Fix the crankshaft with SST.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A109815E02
    Install and uniformly tighten the 10 mounting bolts in several steps in the sequence shown in the illustration.(*1)

    Torque:
    27 N*m{ 276 kgf*cm , 20 ft.*lbf }

    If any one of the mounting bolts does not meet the torque specification, replace the mounting bolt.

  1. A087316E01
    Mark the mounting bolt with paint.(*2)

  1. Retighten the mounting bolt by 90° in the order shown in step (*1).

  1. Check that the painted mark is now at a 90° angle to that in step (*2).


32. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

  1. C104158E01
    Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.
    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc assembly in the wrong direction.


33. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C114265E02
    Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.

  1. Following the procedures shown in the illustration, tighten the 6 bolts starting from the bolt located near the knock pin on the top.

    SST
    09301-00110  

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Evenly tighten the bolts by following the order shown in the illustration.
    2. Tighten the bolts after checking that the disc is in the center by lightly moving the SST up and down, left and right.


34. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. C086210
    Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

    Maximum non-alignment:
    0.9 mm (0.035 in.)

  1. C114266E01
    If alignment is not as specified, adjust the diaphragm spring tip alignment using SST.
    SST
    09333-00013  


35. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

  1. A004869E01
    Apply adhesive to 2 or 3 threads of the mounting bolt end.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the spacer FR, drive plate and spacer RR on the crankshaft.

    NOTICE:
    Do not start the engine for at least 1 hour after installing.

  1. A102138E01
    Fix the crankshaft with SST.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A102156E02
    Install and uniformly tighten the 10 mounting bolts in several steps in the sequence shown in the illustration.

    Torque:
    74 N*m{ 750 kgf*cm , 55 ft.*lbf }


36. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
(Click here)

37. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

38. INSTALL STARTER ASSEMBLY (for 2.0 kW Type)
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire harness with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Close the terminal cap.

  1. Connect the ground cable and wiring harness clamp bracket with the 2 bolts.

    Torque:
    25 N*m{ 251 kgf*cm , 18 ft.*lbf }


39. INSTALL STARTER ASSEMBLY (for 1.7 kW Type)
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire and install the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Close the terminal cap.

  1. Connect the ground cable and wiring harness clamp bracket with the 2 bolts.

    Torque:
    25 N*m{ 251 kgf*cm , 18 ft.*lbf }


40. INSTALL STARTER ASSEMBLY (for 1.6 kW Type)

  1. A113538E01
    Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the wire harness to terminal 30 and install the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the terminal 50 connector to the starter assembly.

  1. A102709E01
    Install the ground cable and wire bracket with the 2 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


41. INSTALL ENGINE ASSEMBLY WITH TRANSMISSION
  1. Using the engine lifter, hold the engine assembly and install the engine assembly w/ transmission.

  1. A101144E05
    Install the stabilizer bracket and 16 bolts of the front suspension cross member.

    Torque:
    Bolt A:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Bolt B:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Bolt C:
    150 N*m{ 1,530 kgf*cm , 111 ft.*lbf }

  1. Connect the rear engine mount.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    Be sure to tighten the nut side.

  1. Remove the engine lifter slowly.


42. CONNECT STEERING TORQUE SHAFT ASSEMBLY

  1. C106143E01
    Align the matchmarks on the steering torque shaft assembly and the power steering link assembly.

  1. C106142E01
    Install bolt (B) and tighten the 2 bolts.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }


43. CONNECT OIL COOLER HOSE (for Automatic Transmission)
  1. Connect the oil cooler inlet hose and outlet hose with the clamp to the oil cooler tube.


44. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

  1. C102933E04
    Install the transmission control cable assembly to the control shaft lever and transmission control bracket No.1 with the nut and a new clip.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }


45. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY (for Automatic Transmission)

  1. C102934E06
    Coat a new O-ring with ATF and install the oil filler tube.

  1. Install the oil filler tube with 2 bolts.

    Torque:
    12 N*m{ 125 kgf*cm , 10 ft.*lbf }


46. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)

  1. C102659E01
    Install 2 new clips to the transmission control cable bracket No.1.

  1. Install the transmission control cable assembly to the transmission control cable bracket No.1.

    NOTICE:
    1. Be sure that A claws of the clips are firmly engaged into the bracket grooves.
    2. Be sure the cable is set in the clip with both B claws erected to prevent slippage of the cable in the opposite direction.

  1. C102206E01
    Align the matchmarks on the control cable assembly and the outer lever.

  1. Install the transmission control cable assembly to the outer levers with the 2 nuts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


47. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

  1. C102209
    Install the clutch release cylinder with the 2 bolts.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }


48. CONNECT SHOCK ABSORBER ASSEMBLY FRONT LH
(Click here)

49. CONNECT SHOCK ABSORBER ASSEMBLY FRONT RH

HINT:
Use the same procedures described for the LH side.


50. CONNECT FRONT SUSPENSION SUB-ASSEMBLY UPPER LH

  1. C102007E02
    Connect the front suspension upper arm to the steering knuckle with the nut.

    Torque:
    113 N*m{ 1,150 kgf*cm , 83 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    1. If the holes for the cotter pin are not aligned, tighten the nut up to 60°.
    2. Do not damage the ball joint dust cover.


51. CONNECT FRONT SUSPENSION SUB-ASSEMBLY UPPER RH

HINT:
Use the same procedures described for the LH side.


52. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

  1. C102283E01
    Install the brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    123 N*m{ 1,250 kgf*cm , 91 ft.*lbf }


53. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


54. INSTALL SPEED SENSOR FRONT LH (w/ ABS)

  1. C102281E01
    Install the speed sensor to the steering knuckle with the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from adhering to the speed sensor.
    2. Be careful not to damage the speed sensor.
    3. Do not twist the sensor wire when installing the speed sensor.


55. INSTALL SPEED SENSOR FRONT RH (w/ ABS)

HINT:
Use the same procedures described for the LH side.


56. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for Super Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller with center bearing shaft assembly in the extension housing.

  1. C107214
    Install the center support bearing assembly No.1, and temporarily tighten the 2 bolts.

  1. C102185E01
    Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }

  1. C107213E01
    Check that the center line of the bracket is at right angles to the shaft axial direction.

  1. C115777E01
    Adjust the center support bearing assembly No.1.

    HINT:
    1. With the vehicle unladen, adjust the center support bearing No.1 to maintain the angles, as shown.
    2. In the same conditions, check the center line in the axial direction. Adjust the bearing if necessary.
    3. The center bearing center line and center bearing housing center line must be adjusted to within -1.0 to 1.0 mm (-0.0394 to 0.0394 in.) of each other in the vehicle's longitudinal direction with the vehicle unladen.

  1. Tighten the 2 bolts.

    Torque:
    36 N*m{ 369 kgf*cm , 27 ft.*lbf }


57. INSTALL PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)

  1. C102186E01
    Remove the SST from the extension housing.

  1. Install the propeller shaft assembly in the extension housing.

  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. C102185E01
    Install the propeller shaft assembly with the 4 nuts, 4 bolts and 4 washers.

    Torque:
    74 N*m{ 755 kgf*cm , 54 ft.*lbf }


58. INSTALL EXHAUST PIPE ASSEMBLY CENTER (for Super Long Wheelbase)
  1. Install a new gasket to the exhaust pipe assembly center.

  1. Connect the exhaust pipe assembly center to the exhaust pipe supports.

  1. Install the exhaust pipe assembly center and exhaust pipe assembly tail with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


59. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Super Long Wheelbase)
  1. w/ Secondary air injection system:

    1. Install the air fuel ratio sensor. (Click here)

      Torque:
      44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. For Unleaded gasoline engine:

    1. Install the oxygen sensor. (Click here)

      Torque:
      44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. Inspect the compression spring.

    1. A077857
      Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. A102062E03
    Install the gasket.

    1. Fully insert a new gasket to the exhaust manifold by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not reuse the gasket.
      3. Do not damage the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe assembly front to force the gasket onto the exhaust manifold.

    3. Install a new gasket to the exhaust pipe assembly front.

    4. Connect the exhaust pipe assembly front to the exhaust pipe support.

    5. Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.

      Torque:
      Exhaust manifold side:
      43 N*m{ 438 kgf*cm , 32 ft.*lbf }
      Exhaust pipe assembly center side:
      48 N*m{ 489 kgf*cm , 35 ft.*lbf }

      NOTICE:
      After installation, check that the clearance is almost the same at any point between the flanges of the exhaust manifold and exhaust pipe assembly front.

  1. For Unleaded gasoline engine:

    1. Connect the sensor connector(s).


60. INSTALL EXHAUST PIPE ASSEMBLY FRONT (for Long Wheelbase)
  1. w/ Secondary air injection system:

    1. Install the fuel ratio sensor. (Click here)

      Torque:
      44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. For unleaded gasoline engine:

    1. Install the oxygen sensor. (Click here)

      Torque:
      44 N*m{ 449 kgf*cm , 32 ft.*lbf }

  1. Inspect the compression spring.

    1. A077857
      Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5mm(1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. A102062E03
    Install the gasket.

    1. Fully insert a new gasket to the exhaust manifold by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not reuse the gasket.
      3. Do not damage the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe assembly front to force the gasket onto the exhaust manifold.

  1. Install a new gasket to the exhaust pipe assembly front.

  1. Connect the exhaust pipe assembly front to the exhaust pipe support.

  1. Install the exhaust pipe assembly front with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust manifold side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    Torque:
    Exhaust pipe assembly tail side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost the same at any point between the flanges of the exhaust manifold and exhaust pipe assembly front.

  1. For unleaded gasoline engine:

    1. Connect the sensor connector(s).


61. CONNECT ENGINE WIRE
  1. Connect the +B terminal and connector of the starter.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A101143E04
    Install the connectors and nut as shown in the illustration.

  1. Connect the clamps of the engine wire and earth cable.

  1. Connect the connectors of the ECM.

  1. Install the wire harness support of the engine ECM.


62. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)

  1. A102804E01
    Temporarily install the bolt A to install the compressor.

  1. Install the compressor completely by tightening the 4 bolts in the order shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    In order to prevent misalignment, which causes belt rattle, tightening of the bolts must be performed in the order shown.

  1. Connect the suction tube clamp with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the compressor connector.


63. INSTALL OIL LEVEL GAUGE GUIDE

  1. A102132E01
    Install the gauge guide with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


64. INSTALL OIL LEVEL GAUGE SUB-ASSEMBLY

65. INSTALL VANE PUMP ASSEMBLY

  1. A102130E01
    Install the vane pump with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the PS fluid pressure switch connector.


66. CONNECT FUEL HOSE NO.2
  1. Connect the fuel hose No.2 to the delivery pipe.


67. CONNECT FUEL HOSE
  1. Align the connector and pipe. Push on the connector until the retainer locks with a click sound. (Click here)

  1. Pull the connector to check that the connector is securely connected. (Click here)

  1. A087756E01
    Install the connector and lock it with the fuel hose connector cover. (Click here)


68. CONNECT AIR HOSE NO.5 (w/ Secondary Air Injection System)
  1. Connect the air hose No.5 to the air switching valve.


69. INSTALL INTAKE AIR CONNECTOR
  1. Temporarily install the intake air connector to the throttle body assembly.

  1. A102437E03
    Connect the No. 2 ventilation hose and vacuum hose, and slide the clamp to secure it. (A)

  1. Install the intake air connector with the 2 bolts. (B)

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the 2 hose clamp bolts. (C)

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


70. INSTALL AIR PRESSURE SENSOR (w/ Manifold Absolute Pressure Sensor)
  1. Install the air pressure sensor with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air pressure sensor together with the bracket with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Attach the wire harness clamp.

  1. Connect the vacuum hose and clamp.

  1. Connect the connector.


71. CONNECT UNION TO CONNECTOR TUBE HOSE
  1. Connect the union to connector tube hose to the intake manifold.


72. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

  1. A103325
    Connect the fuel vapor feed hose to the VSV.


73. CONNECT HEATER WATER HOSE OUTLET B
  1. Connect the heater water outlet hose B to the heater unit.


74. CONNECT HEATER WATER HOSE INLET A
  1. Connect the heater water inlet hose A to the heater unit.


75. CONNECT RADIATOR HOSE OUTLET
  1. Connect the radiator outlet hose to the clamp.


76. CONNECT RADIATOR HOSE INLET
  1. Connect the radiator inlet hose to the clamp.


77. INSTALL FAN & GENERATOR V BELT

G035171E02
  1. Install the drive belt to the pulleys except the drive belt tensioner pulley.

  1. Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward and then install the drive belt to the tensioner pulley.

    NOTICE:
    1. The backside of the drive belt should face the tensioner pulley.
    2. Check that the drive belt is properly set to each pulley.

  1. G036496E02
    After a new belt has been installed, check that the tensioner indicator mark is within range A shown in the illustration.


78. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


79. INSTALL FRONT DOOR SCUFF PLATE

80. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
  1. Perform the same procedure as above on the opposite side. (Click here)


81. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
  1. Perform the same procedure as above on the opposite side. (Click here)


82. INSTALL FRONT WHEELS

Torque:
100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }


83. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

84. CONNECT BATTERY NEGATIVE CABLE

85. ADD ENGINE OIL

86. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block water drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Fill the radiator reservoir assembly with engine coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Rear Heater
    11.2 liters (11.8 US qts, 9.9 Imp. qts)
    w/ Rear Heater
    13.2 liters (13.9 US qts, 11.6 Imp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the 2-way that is located near the throttle body assembly.

  1. When air is bled and the engine coolant drains out, install the 2-way.

  1. Add coolant through the radiator reservoir assembly filler opening until the coolant reaches the B line and install the radiator reservoir cap sub-assembly. [*1]

  1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes. [*2]

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fans.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir assembly does not have any engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant.
    2. Do not start the engine when there is no engine coolant in the radiator reservoir assembly.
    3. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough engine coolant, the engine may overheat.

    HINT:
    1. Press the No. 2 and No. 3 radiator hoses several times by hand, and then check the level of the engine coolant.
    2. The thermostat open timing can be confirmed by pressing the No. 3 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature. [*3]

  1. Check the engine coolant level in the radiator reservoir assembly. [*4]

    HINT:
    1. If the engine coolant level is below the LOW line, repeat step *1 through *4.
    2. If the engine coolant level is above the FULL line, drain engine coolant until the engine coolant level is between the FULL and LOW lines.


87. INSPECT FUEL LEAKS
  1. When using the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the on position and intelligent tester main switch ON.

      NOTICE:
      Do not start the engine.

    3. Select the Active Test mode on the intelligent tester.

      HINT:
      Please refer to the intelligent tester operator's manual for further details.

  1. When not using the intelligent tester.

    1. A103380E01
      Disconnect the fuel pump connector.

    2. Using a service wire, connect terminals FP and +B of the relay block.

      NOTICE:
      Pay attention to the terminal connecting position to avoid a malfunction.

    3. Turn the ignition switch to the ON position, and check that the fuel pump operates.

      NOTICE:
      Do not start the engine.

  1. Check that there are no fuel leaks anywhere on the fuel system after doing maintenance.

  1. Check that the pulsation damper screw rises up when the fuel pump operates.
    If operation is not as specified, check the following parts:

    1. Fusible link
    2. Fuel pump
    3. Wiring connections
    4. ECM
    5. Fuses

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.


88. INSPECT ENGINE OIL LEAKS

89. INSPECT MANUAL TRANSMISSION OIL (for Manual Transmission)

  1. D025304E01
    Park the vehicle in a level place.

  1. Remove the transmission filler plug and gasket.

  1. Check that the oil surface is within 5 mm (0.20 in.) below the lowest point of the transmission filler plug opening.

    Oil grade:
    API GL-4
    Viscosity:
    SAE 75W-90
    Capacity:
    2.6 liters (2.7 US qts, 2.3 Imp.qts)

    NOTICE:
    1. Problems may occur when the oil level is too high or too low.
    2. After replacing the oil, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transmission filler plug and a new gasket.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


90. INSPECT AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

HINT:
Drive the vehicle so that the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. D025120E01
    Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move shift the lever into all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put it back all the way.

  1. Take it out again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.


91. INSPECT ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


92. INSPECT SHIFT LEVER POSITION (for Automatic Transmission)
  1. When shifting from P position only with ignition switch ON and depress the break pedal.

  1. Make sure that the shifting lever moves smoothly and can be moderately operated.

  1. When starting engine, make sure that the vehicle moves forward when shifting from N to D position and moves reward when shifting R position.


93. ADJUST SHIFT LEVER POSITION (for Automatic Transmission)

  1. C101771E02
    Remove a clip, nut, and disconnect between the control shaft lever to transmission control cable assembly from the control shaft lever and transmission control cable bracket No.1.

  1. C101788E05
    Turn the control shaft lever until stop to a clockwise direction, return the control shaft lever 2 notches to N position.

  1. C101803
    Set the shift lever to N position while holding the shift lever lightly toward the R position side and install it.

    Torque:
    15 N*m{ 150 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Tighten the nut with it closing up cranky.

  1. Inspect the operation condition and work.


94. INSPECT EXHAUST GAS LEAKS

95. ADJUST FRONT WHEEL ALIGNMENT
(Click here)

96. INSTALL ENGINE SIDE UNDER COVER RH (w/ Engine Side Under Cover RH)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }


97. INSTALL ENGINE SIDE UNDER COVER LH (w/ Engine Side Under Cover LH)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }


98. INSTALL ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }


99. INSTALL ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

Torque:
13 N*m{ 133 kgf*cm , 10 ft.*lbf }


100. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Start the engine and idle it.

    3. Turn the intelligent tester main switch on.

    4. Enter the following items:
      Powertrain / Engine and ECT / Data list / IGN Advance

      Ignition timing:
      5 to 15° BTDC at idle

      HINT:
      Refer to the intelligent tester operator's manual for further detail.

  1. When not using the intelligent tester:

    1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No.4 cylinder.

      NOTICE:
      1. Use a timing light that detects the first signal.
      2. After checking, be sure to wrap the wire harness with tape.

    2. Turn the ignition switch to the ON position.

    3. A115055E01
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. When checking the ignition timing, the transmission should be in the neutral.

      HINT:
      1. After connecting terminals (TC and CG), engine rpm changes to approximately 1,000 to 1,500 rpm for 5 seconds, then returns to idle speed. This is because the ECM checks that the ISC (idle speed control system) operates properly.
      2. Perform the inspection of the ignition timing after engine rpm is returned to idle speed.

    4. Inspect the ignition timing

      Ignition timing:
      3 to 7° BTDC at idle

    5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    6. Inspect the ignition timing

      Ignition timing:
      5 to 15° BTDC at idle

    7. Check that the ignition timing advances immediately when the engine speed is increased.

    8. Turn the ignition switch off.

    9. Remove the timing light.


101. INSPECT IDLE SPEED
  1. Warm up and stop the engine.

    NOTICE:
    A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

    2. Start the engine and idle it.

    3. Turn the intelligent tester main switch on.

    4. Enter the following items:
      Powertrain / Engine and ECT / Data list / Engine SPD

      Idle speed:
      600 to 700 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be in the neutral position.
      2. Switch off all accessories and air conditioning before connecting the intelligent tester.

    5. Turn the ignition switch off.

    6. Disconnect the intelligent tester from the DLC3.

  1. A059802E01
    When not using the intelligent tester:

    1. Install SST to terminal 9 (TAC) of DLC3, then connect a tachometer.

      SST
      09843-18030  

      NOTICE:
      Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    2. Turn the ignition switch to the ON position.

    3. Inspect the engine idling speed.

      Idle speed:
      600 to 700 rpm

    4. Turn the ignition switch off.

    5. Disconnect the tachometer.

    6. Remove the SST from terminal 9 (TAC).

      SST
      09843-18030  


102. INSPECT CO (for Leaded Gasoline Specification Vehicle)

HINT:
This check is used only to determine whether or not the idle CO complies with regulations.

  1. Initial condition:

    1. Engine at normal operating temperature

    2. Air cleaner installed

    3. All pipes and hoses of the air induction system connected

    4. All accessories switched off

    5. All vacuum lines properly connected

    6. EFI system wiring connectors fully seated

    7. Ignition timing set correctly

    8. Transmission in the neutral position

    9. Tachometer and CO meter calibration at idle

      NOTICE:
      If a CO meter is not available, do not attempt to adjust the idle mixture. Always use a CO meter when adjusting the idle mixture. It is unnecessary to use the idle mixture screw for adjustments if the vehicle is in good condition.

  1. Warm up the engine by driving at constant speed (approximately 50 km/h (31 mph)). Close the throttle valve for 5 minutes after the engine coolant temperature becomes stable (80 to 90°C (176 to 194°F)) and idle the engine for 5 minutes.

  1. A109838E01
    Insert a tester probe at least 40 cm (1.3 ft) into the tail pipe.

  1. Wait at least 1 minute before measurement to allow the concentration to stabilize. Complete the measurement within 3 minutes.

    Idle CO concentration:
    1.0 to 2.0%

  1. A001435E01
    If the CO concentration does not conform to regulations, adjust it by turning the idle mixture adjusting screw in the variable resistor with SST.
    SST
    09243-00020  

  1. A001434E01
    The idle mixture adjusting screw can be adjusted within an 180° angle range.

    HINT:
    1. If the CO concentration is within the specification, this adjustment is complete.
    2. If the CO concentration cannot be corrected by idle mixture adjustment, see the table below for other possible causes.

  1. Remove the SST.

    CO
    Problems
    Causes
    High
    Rough idle (black smoke from exhaust)
    1. Clogged air filter
    2. Plugged ventilation valve
    3. Faulty SFI system:
      1. Faulty fuel pressure regulator
      2. Clogged fuel return line
      3. Defective engine coolant temperature (ECT) sensor
      4. Faulty ECM
      5. Faulty injectors
      6. Faulty throttle position sensor
      7. Faulty MAF meter


103. INSPECT CO,HC (for Unleaded Gasoline Specification Vehicle)

HINT:
The ECM properly controls the CO/HC concentration in the emission gas.

  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tail pipe while idling.

  1. Check the CO/HC concentration with the engine idling and/or running at 2,500 rpm.

    HINT:
    1. If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
    2. Check the heated oxygen sensor operation (Click here).
    3. Check the heated air fuel ratio sensor operation (Click here).
    4. See the table below for possible causes, then inspect the applicable causes and repair them if necessary.

    CO
    HC
    Problems
    Causes
    Normal
    High
    Rough idle
    1. Faulty ignitions:
      1. Incorrect timing
      2. Fouled, shorted or improperly gapped plugs
    2. Incorrect valve clearance
    3. Leaks in intake and exhaust valves
    4. Leaks in cylinders
    Low
    High
    Rough idle (Fluctuating HC reading)
    1. Vacuum leaks:
      1. PCV hoses
      2. Intake manifold
      3. Throttle body
      4. Brake booster line
    2. Lean mixture causing misfire
    High
    High
    Rough idle (Black smoke from exhaust)
    1. Restricted air filter
    2. Plugged PCV valve
    3. Faulty SFI systems:
      1. Faulty pressure regulator
      2. Defective engine coolant temperature sensor
      3. Defective mass air flow meter
      4. Faulty ECM
      5. Faulty injectors
      6. Faulty throttle body


104. INSPECT FUNCTION OF THROTTLE BODY

  1. Check the throttle control motor operating sounds.

    1. Turn the ignition switch to the ON position.

    2. A113033
      When pressing the accelerator pedal, listen to the running sounds of the motor. Make sure no friction noise comes from the motor.
      If friction noise exists, replace the throttle body.

  1. A082779E02
    Check the throttle position sensor.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position.

    3. Turn the intelligent tester main switch on.

    4. Enter the following menus: Power train / Engine / Data List / Throttle Sensor Position and Throttle Position Sensor Position #2.

    5. Depress the accelerator pedal. When the throttle valve is fully opened, check that the value of the "Throttle Sensor Position" is within the specification.

      Standard throttle valve opening percentage:
      60% or more

      NOTICE:
      When checking the standard throttle valve opening percentage, the shift lever should be in the N position.

      HINT:
      If the percentage is less than 60%, replace the throttle body.


105. INSPECT ABS SENSOR SIGNAL (w/ ABS)
(Click here)

106. PERFORM INITIALIZATION
(Click here)
← REMOVAL (from Jan 2017)INSTALLATION (from Jan 2017) →