2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Oct 2014


1. INSTALL FUEL TEMPERATURE SENSOR

  1. A078244E01
    Apply a light coat of light oil to a new O-ring.

  1. Install the O-ring to the fuel temperature sensor.

  1. Using the SST, install the fuel temperature sensor.

    SST
    09922-10010  

    Torque:
    22 N*m{ 220 kgf*cm , 16 ft.*lbf }


2. INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY

  1. A070715
    Confirm that the supply pump gear in the timing gear case moves back and forth smoothly.

  1. Install a new O-ring and the pulley key to the supply pump.

  1. Aligning the projecting edge of the supply pump head to the key-slot of the supply pump gear, install the pump to the timing gear case.

  1. While holding the supply pump by hand, push the supply pump gear rearward to engage the pump gear and drive shaft.

  1. Temporarily install the supply pump with the 2 nuts.

  1. A077989
    Using SST, hold the crankshaft.
    SST
    09213-58013  
    09330-00021  

  1. Install the supply pump gear set nut.

    HINT:
    Set a new O-ring before tightening the supply pump gear set nut.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. A076978
    Temporarily install the supply pump stay with the 2 bolts on the engine block side.

  1. Tighten the 2 nuts for the injection pump.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. A070710
    Install the camshaft timing pulley flange No.2 and pump drive shaft pulley with the 4 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }


3. CHECK PUMP DRIVE SHAFT THRUST CLEARANCE

  1. A071144
    Push the pump drive shaft pulley back and forth to check a thrust clearance of the injection pump drive shaft.

    Thrust clearance:
    0.15 to 0.55 mm (0.0059 to 0.0217 in.)

    NOTICE:
    Make sure that the crankshaft pulley's notch is at 30 degree in the counterclockwise direction form the TDC position.

    HINT:
    If there is not thrust clearance, disassemble and reassemble the injection pump and pump drive shaft pulley.


4. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
  1. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket, or timing gear case with a new one, replace the fuel inlet pipe.
  2. Be careful not to adhere dusts, dirt or any other materials onto the joint area of the fuel inlet pipe.

  1. Temporarily install the fuel inlet pipe.

  1. Using SST, tighten the injection pipe on the common rail side.

    SST
    09023-12701  

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with SST

  1. Using SST, tighten the injection pipe on the supply pump side.

    SST
    09023-12701  

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with SST


5. INSTALL INJECTION PIPE
SST
09023-12701  

NOTICE:
  1. When replacing the fuel injector, common rail, or cylinder head with a new one, replace injection pipes No. 1, No. 2, No. 3, and No. 4.
  2. Keep clean the joint of the injection pipe.

  1. Install the injection pipes.

    1. A103532
      Temporarily install the 4 injection pipes.

    2. A103526
      Install the injection pipe clamp No.3 in 2 nuts.

      Torque:
      5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    3. A103532E01
      Fasten the union sequentially, from the injection pipe common rail to the injector, using SST.
      SST
      09023-12701  

      Torque:
      Use union nut wrench and torque wrench:
      32 N*m{ 326 kgf*cm , 24 ft.*lbf }


6. INSTALL OIL LEVEL GAGE GUIDE
  1. Install a new O-ring to the oil level gauge guide.

  1. Apply a light coat of engine oil to the O-ring.

  1. Install the oil level gauge guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the oil level gauge.


7. CONNECT INTAKE AIR CONNECTOR (w/o EGR Valve)

  1. A106848E01
    Temporarily install 2 new gaskets and intake air connector No.2 to the intake air connector.

  1. A106846
    Temporarily tighten the intake air connector assembly with the bolt and 2 nuts.

  1. Tighten the manifold stay with the bolt.

  1. Tighten the intake air connector with the bolt and 2 nuts.

  1. Install the vacuum hose to the intake air connector.


8. TEMPORARILY TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)

  1. Temporarily tighten the EGR valve assembly with the sensor.

    1. A115761E01
      Install 2 new gaskets and the EGR valve to the intake air connector as shown in the illustration.

    2. A102287
      Temporarily tighten the intake air connector with EGR valve assembly to the intake manifold with the bolt and the 2 nuts.

    3. Install the vacuum hose to the intake air connector.

    4. Temporarily tighten the manifold stay with the bolt.

    5. A103043
      Connect the EGR valve position sensor connector.

    6. Connect the intake air temperature sensor connector.

  1. Install the vacuum regulating valve.

    1. A103046
      Install the vacuum regulating valve with the 2 bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Connect the 2 vacuum hoses and the regulating valve connector.


9. INSTALL EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)

  1. A106845
    Install the 2 gaskets to the cylinder head and EGR pipe sub-assembly as shown in the illustration.

  1. A106844
    Install the EGR pipe sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Tighten the intake air connector with the bolt and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Tighten the manifold stay.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


10. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)
  1. Remove the 3 bolts, the 2 nuts, and the EGR pipe sub-assembly.

  1. Remove the 2 gaskets.


11. INSTALL DIESEL THROTTLE BODY ASSEMBLY

NOTICE:
After removing and installing, or replacing the throttle body, be sure to perform the operation check.

  1. Install a new gasket to intake air connector.

  1. A102902
    Install the throttle body with the 2 bolts and the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A102282
    Connect the 2 throttle body connectors.


12. INSTALL AIR HOSE NO.4

  1. A102281
    Install the air hose No.4 with the 2 clamps.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


13. INSTALL EGR PIPE SUB-ASSEMBLY (w/ EGR Valve)

  1. A106845
    Install 2 new gaskets to the cylinder head and the EGR pipe sub-assembly No.1 as shown in the illustration.

  1. A106844
    Install the EGR pipe with the 2 bolts and the 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A106043
    Connect the fuel pressure sensor connector.


14. INSTALL OIL RETURN HOSE

  1. A106042
    Connect the oil return hose with the clip.


15. INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A102278
    Install the vane pump oil reservoir assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


16. INSTALL TIMING BELT

  1. A070691E01
    Check that the timing marks are aligned as shown in the illustration.

  1. Install the timing belt to pump drive shaft pulley, camshaft timing pulley and timing belt idler No.1 in sequence.

  1. A070548
    Set the tensioner to the press upright.

    NOTICE:
    1. Do not allow the rod end to scratch and deform.
    2. Press the tensioner rod in upward.
    3. Protect a tip of the push rod with a rag in order to prevent damage.

  1. Using a press, slowly apply 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force to the push rod.

    NOTICE:
    Do not apply loads 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) or more on the push rod.

  1. Align the holes of push rod and housing, pass a 1.27 mm hexagon wrench through the holes to keep the setting position of the push rod.

  1. Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.

  1. Tighten the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Uniformly tighten the 2 bolts and install the tensioner

  1. Remove the 1.5 mm hexagon wrench from the tensioner.

  1. A070549E01
    Turn the crankshaft in the clockwise direction twice, check that the timing marks are aligned as shown in the illustration.


17. INSTALL TIMING BELT COVER NO.1

  1. A102815
    Install the timing belt No.1 cover with the 6 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the wire harness clamp.


18. INSTALL FAN & GENERATOR V BELT
  1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.

    NOTICE:
    Make sure that the fan and generator V belt is set properly on each pulley.

  1. Check that the indicator mark of the V-ribbed belt tensioner (Click here).


19. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the engine service hole sub cover with the 5 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


20. INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

  1. B107528
    Connect the front seat inner belt assembly connector and install the front seat assembly.

  1. Align the front seat assembly adjuster pin with the holes in the body.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the front side of the front seat assembly.

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


21. INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

  1. B107542
    Connect the front seat inner belt assembly connector and install the front seat assembly.

  1. Align the front seat assembly adjuster pin with the holes in the body.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the front side of the front seat assembly.

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


22. INSTALL FRONT DOOR SCUFF PLATE RH

23. CONNECT BATTERY NEGATIVE CABLE

24. BLEED FUEL LINE

  1. A114068E01
    Using the hand pump, bleed air from the fuel system until pumping becomes difficult.


25. CHECK FOR FUEL LEAKAGE
  1. PERFORM ACTIVE TEST

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch on.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    5. Perform the Active Test.

      Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizes common rail internal fuel pressure, and checks for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when ON is selected
      2. Above conditions preserved while test is ON

← INSPECTION (from Oct 2014)COMPONENTS (from Oct 2014) →