2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


1. REMOVE CONDENSER WITH RECEIVER ASSEMBLY
(Click here)

2. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the engine coolant in a container and dispose of it according to the local regulations.

  1. Loosen the radiator drain cock plug and drain the engine coolant.

    A316605E01

    Text in Illustration 
    *1
    Radiator Reservoir Cap Sub-assembly
    *2
    Radiator Reservoir Assembly
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Water Drain Cock Plug
    *5
    2-Way
    -
    -

  1. Remove the radiator reservoir cap sub-assembly.

  1. Loosen the cylinder block water drain cock plug and drain the engine coolant from the engine.


3. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. A316620
    Remove the 2 clips, 4 bolts and upper radiator support seal.


4. REMOVE RADIATOR RESERVOIR ASSEMBLY

  1. A316482
    Slide the hose clamp and disconnect the water by-pass hose from the radiator reservoir assembly.

  1. Slide the hose clamp and disconnect the No. 2 water by-pass hose from the radiator reservoir assembly.

  1. Remove the bolt and radiator reservoir assembly.


5. REMOVE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

  1. A316480
    Disconnect the connector from the windshield washer motor and pump assembly.

  1. Remove the 2 bolts and windshield washer motor and pump assembly.

  1. Detach the hose clamp.

    A316481E01

    Text in Illustration 
    *A
    w/ Rear Wiper
    *B
    w/o Rear Wiper

  1. w/ Rear Wiper:
    Disconnect the 2 connectors and 2 washer hoses.

  1. w/o Rear Wiper:
    Disconnect the connector and washer hose.


6. REMOVE HOOD LOCK ASSEMBLY

  1. A243233
    Remove the 3 bolts and disconnect the hood lock assembly.

  1. Remove the hood lock assembly from the hood lock control cable assembly.


7. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
  1. Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.

  1. A316619
    Detach the 2 clamps to disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.

  1. Remove the 6 bolts and upper radiator support sub-assembly.


8. REMOVE FAN BRACKET ASSEMBLY
  1. Disconnect the 4 connectors from the No. 1 and No. 2 cooling fan ECUs.

  1. A116095
    Remove the 2 bolts, 2 nuts, and fan bracket assembly together with the No. 1 and No. 2 cooling fan ECUs.


9. DISCONNECT OIL COOLER HOSE

  1. A103436E03
    Detach the 2 oil cooler hose clamps.

  1. Slide the hose clamp and disconnect the inlet oil cooler hose from the oil cooler tube.

  1. Slide the hose clamp and disconnect the outlet oil cooler hose from the oil cooler tube.


10. DISCONNECT NO. 2 RADIATOR HOSE
  1. Slide the hose clamp and disconnect the No. 2 radiator hose from the radiator assembly.


11. DISCONNECT NO. 3 RADIATOR HOSE
  1. Slide the hose clamp and disconnect the No. 3 radiator hose from the radiator assembly.


12. REMOVE FAN SHROUD

  1. A116240
    Remove the 6 bolts and fan shroud from the underside of the vehicle.


13. REMOVE NO. 2 FAN SHROUD

  1. A316618
    Slide the hose clamp and remove the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.

  1. Remove the bolt to disconnect the water by-pass pipe sub-assembly from the radiator assembly.

    HINT:
    This procedure is performed because the bolt of the water by-pass pipe sub-assembly interferes with the removal of the No. 2 fan shroud.

  1. A314980
    Remove the 2 bolts and No. 2 fan shroud from the underside of the vehicle.

    NOTICE:
    Do not damage the radiator assembly when removing the No. 2 fan shroud.


14. REMOVE RADIATOR ASSEMBLY

  1. A316606
    Remove the radiator assembly from the vehicle.

    NOTICE:
    Do not drop the radiator assembly.

  1. Remove the 4 grommets from the radiator assembly.


15. REMOVE OIL COOLER HOSE

  1. A316639
    Slide the hose clamp and remove the inlet oil cooler hose from the radiator assembly.

  1. Slide the hose clamp and remove the outlet oil cooler hose from the radiator assembly.


16. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

  1. A316602
    Slide the hose clamp and remove the water by-pass pipe sub-assembly from the radiator assembly.

← COMPONENTS (from Oct 2014)REMOVAL (from Jan 2015) →