2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. DRAIN ENGINE COOLANT

A316990E01

CAUTION:
To avoid the danger of being burned, do not remove the reservoir cap while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain plug.

  1. Remove the reservoir cap.

  1. Loosen the cylinder block drain plug and drain the coolant.

  1. Tighten the radiator drain plug.

  1. Tighten the cylinder block drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


2. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


3. REMOVE FRONT DOOR SCUFF PLATE RH

4. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Turn back the carpet, and remove the engine service hole cover sub-assembly.


5. REMOVE RADIATOR HOSE INLET

6. REMOVE RADIATOR HOSE NO.4

7. REMOVE VANE PUMP V BELT

  1. A071310E01
    Loosen the bolt A and nut B, and remove the V belt.


8. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (w/ Air Conditioning System)

  1. A074095E01
    Loosen the nut A and bolt B, and remove the V belt.


9. REMOVE FAN & GENERATOR V BELT (w/ Air Conditioning System)

  1. A115632E01
    Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.


10. REMOVE FAN & GENERATOR V BELT (w/o Air Conditioning)

  1. A115631E01
    Loosen the bolts A and B, and remove the V belt.


11. REMOVE WATER PUMP PULLEY

12. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
(Click here)

13. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A112014
    Remove the 3 bolts and compressor mounting bracket.

  1. A112016
    Remove the bolt and spacer.

  1. A112015
    Remove the 4 bolts and compressor mounting bracket.


14. REMOVE VANE PUMP PULLEY

  1. C106133E01
    Using SST, remove the nut and the vane pump pulley.
    SST
    09960-10010   (09962-01000, 09963-01000)


15. REMOVE CRANKSHAFT PULLEY
SST
09213-54015   (91651-60855)
09330-00021  
09950-50013   (09951-05010, 09952-05010, 09953-05010, 09953-05020, 09954-05030)

16. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  1. A112017
    Remove the 11 bolts, washers, timing belt cover and 2 gaskets.


17. REMOVE TIMING BELT GUIDE
  1. Remove the timing belt guide.


18. SET NO.1 CYLINDER TO TDC/COMPRESSION

  1. A058728E01
    Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.

  1. A058729E01
    Check that the timing marks of the camshaft timing pulley and No.2 timing belt cover are aligned.
    If not, turn the crankshaft 1 revolution (360°).


19. REMOVE TIMING BELT

  1. A058721E01
    Remove the timing belt.

    HINT:
    If reusing the timing belt, draw a direction arrow on the timing belt (in the direction of engine revolution), and place matchmarks on the pulleys and timing belt.

  1. A058730E01
    Turn the crankshaft 90° counterclockwise, and put the timing mark of the crankshaft timing pulley with the protrusion of the timing gear case.

    NOTICE:
    If the timing belt is disengaged, having the crankshaft timing pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley, causing damage. So always set the crankshaft pulley at the correct angle.

  1. A058731E01
    Loosen the timing belt idler No.1 bolt (A), and shift the idler to the left as far as possible.

  1. Temporarily tighten the pulley bolt (A), and then relieve the timing belt tension.

  1. Remove the timing belt.


20. REMOVE WATER PUMP ASSEMBLY

  1. A031001
    Remove the 6 bolts and tension spring bracket.

  1. Remove the water pump and gasket.

← REMOVAL (Oct 2014 – Dec 2016)INSTALLATION (Oct 2014 – Dec 2016) →