2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. INSTALL WATER PUMP ASSEMBLY
  1. Install a new gasket, the water pump and tension spring bracket with the 6 bolts.

    Torque:
    23 N*m{ 230 kgf*cm , 17 ft.*lbf }


2. INSTALL TIMING BELT
SST
09960-10010   (09962-01000, 09963-01000)

3. SET NO.1 CYLINDER TO TDC/COMPRESSION

  1. A071316E01
    Using the crankshaft pulley bolt, align its groove with the timing pointer by turning the crankshaft clockwise.

    NOTICE:
    Do not turn the crankshaft pulley counterclockwise.

  1. A071317E01
    Set the timing and drive pulleys at each position.

    NOTICE:
    1. The engine should be cold.
    2. When turning the crankshaft or camshaft, the valve heads will hit against the piston top. Do not turn them more than necessary.


4. INSTALL TIMING BELT GUIDE

  1. A058736E01
    Install the belt guide with the cup side facing outward.


5. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
  1. Remove the 2 nuts and wire harness clamp bracket.

  1. A112018E01
    Install the 2 gaskets to the timing belt cover.

  1. A112017
    Install the timing belt cover with the 11 bolts.

    Torque:
    11 N*m{ 105 kgf*cm , 8 ft.*lbf }

  1. Install the 2 nuts and wire harness clamp bracket.


6. INSTALL CRANKSHAFT PULLEY
SST
09213-54015   (91651-60855)
09330-00021  

7. INSTALL VANE PUMP PULLEY

  1. C106134E01
    Using SST, install the vane pump pulley to the vane pump assembly.
    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }


8. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Temporarily install the compressor mounting bracket with the 4 bolts.

  1. A112015E01
    Using several steps, uniformly install and tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    85 N*m{ 870 kgf*cm , 63 ft.*lbf }

  1. A112016
    Temporarily tighten the bolt and spacer.

  1. A112014E01
    Temporarily install the compressor mounting bracket with the 3 bolts.

  1. Using several steps, uniformly install and tighten the 3 bolts in the sequence shown in the illustration.

    Torque:
    47 N*m{ 475 kgf*cm , 36 ft.*lbf }


9. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
(Click here)

10. INSTALL FAN & GENERATOR V BELT (w/o Air Conditioning)

  1. A115631E01
    Install the V belt.

  1. Using a bar, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the tension of the V belt. (Click here)


11. INSTALL FAN & GENERATOR V BELT (w/ Air Conditioning System)

  1. A115632E01
    Install the V belt.

  1. Tightening the bolt C, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the tension of the V belt. (Click here)


12. INSTALL V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1

  1. A074095E01
    Install the V belt.

  1. Tightening the bolt B, adjust the tension of the V belt.

  1. Tighten nut A.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. Check the tension of the V belt. (Click here)


13. INSTALL VANE PUMP V BELT (w/ Air Conditioning System)

  1. A071310E01
    Install the V belt.

  1. Using a bar, adjust the tension of the V-ribbed belt.

  1. Tighten the bolt A and nut B.

    Torque:
    Bolt (A):
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }
    Nut (B):
    64 N*m{ 635 kgf*cm , 47 ft.*lbf }

  1. Check the tension of the V belt. (Click here)


14. INSTALL WATER PUMP PULLEY

15. CONNECT RADIATOR HOSE NO.4

16. CONNECT RADIATOR HOSE INLET

17. ADD ENGINE COOLANT
  1. Fill the radiator reservoir assembly with coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    12.3 liters (13.0 US qts, 10.8 Imp. qts)
    w/ Front Heater
    13.3 liters (14.1 US qts, 11.7 Imp. qts)
    w/ Front and Rear Heaters
    15.3 liters (16.2 US qts, 13.5 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A142533
    Add coolant up to the B line mark in the radiator reservoir assembly and install the reservoir cap.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the coolant level is between the LOW and FULL level marks.


18. START THE ENGINE

19. CHECK FOR ENGINE COOLANT LEAKS

20. INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Install the 5 bolts and engine service hole cover.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


21. INSTALL FRONT DOOR SCUFF PLATE RH

22. INSTALL FRONT SEAT ASSEMBLY RH

  1. B107528
    Connect the front seat inner belt assembly connector and install the front seat assembly.

  1. Align the front seat assembly adjuster pin with the holes in the body.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the front side of the front seat assembly.

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.

  1. Move the front seat assembly to the rearmost position.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Move the front seat assembly fully forward.

    NOTICE:
    Make sure that the front seat assembly is securely locked.

  1. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

← REMOVAL (from Jan 2017)INSTALLATION (from Jan 2017) →